Pliers
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Manufactured to the very highest standards of quality and safety. Fully certified to EN 60900 IEC 900 standard.
• At a temperature of -20ºC the handles must withstand impact and shock loads.
• After 24 hours immersion in water, the pliers must still provide protection against discharges and spark-over at up to 10,000V AC.
• After 2 hours at +70ºC, the pliers must not conduct discharge at a test of 5,000V AC even with a point load of 20N applied.
• After 168 hours (1 week) at +70ºC, the handles must still be firmly secured to the pliers and be able to withstand a 500N pull-off test.
• The handles must be manufactured from near inflammable materials. This is tested using a gas flame.
• All pliers are manufactured from high grade tool steel and are hardened using a special high frequency induction process. Cutting capacities quoted according to DIN/ISO 5744.• VDE Approved.
• Induction hardened cutting edges.
• Soft grip handles for comfort and control.
• Cutting Capacity: Ø1.6mm.
• Meets DIN 5236/ISO 5748.
• Model No. AK83512• VDE Approved long nose pliers with induction hardened cutters in a polished finish.
• Supplied with soft grip handles for comfort and control.
• Wire cutting capacities quoted according to DIN 5236/ISO 5748.160mm Long Nose Pliers - VDE Approved
• Induction-hardened cutting edges.
• Soft grip handles for comfort and control.
• Cutting Capacities: Ø1.8, Ø2.0 & Ø2.3mm.
• Model No. AK83452• VDE Approved pliers with induction-hardened cutting edges in a polished finish.
• Supplied with soft grip handles for comfort and control.
• Cutting capacities according to DIN 5236/ISO 5748 and DIN 5238/ISO 5749.
• Combination pliers meet DIN 5244/ISO 5746 standards.3pc VDE Approved Pliers Set
Manufactured to the very highest standards of quality and safety. Fully certified to EN 60900 IEC 900 standard.
• At a temperature of -20ºC the handles must withstand impact and shock loads.
• After 24 hours immersion in water, the pliers must still provide protection against discharges and spark-over at up to 10,000V AC.
• After 2 hours at +70ºC, the pliers must not conduct discharge at a test of 5,000V AC even with a point load of 20N applied.
• After 168 hours (1 week) at +70ºC, the handles must still be firmly secured to the pliers and be able to withstand a 500N pull-off test.
• The handles must be manufactured from near inflammable materials. This is tested using a gas flame.
• All pliers are manufactured from high grade tool steel and are hardened using a special high frequency induction process. Cutting capacities quoted according to DIN/ISO 5744.• VDE Approved.
• Induction hardened cutting edges.
• Soft grip handles for comfort and control.
• Cutting Capacity: Ø1.6mm.
• Meets DIN 5236/ISO 5748 Standards.
• Model No. AK83562• VDE Approved snipe nose pliers with induction hardened cutting edges in a polished finish.
• Supplied with soft grip handles for comfort and control.
• Cutting capacities according to DIN 5236/ISO 5748.160mm Snipe Nose Pliers - VDE Approved
• Soft grip handles for comfort and control.
• Suitable for wire and cables up to Ø5mm.
• Meets DIN/ISO 5743/4, 8979 Standards.
• Model No. AK83552• VDE Approved wire and cable strippers with screw adjustment.
• Suitable for wire and cables up to Ø5mm.
• Meets DIN/ISO 5743/4, 8979 standards.160mm Wire Stripping Pliers - VDE Approved