Intake Plenum + 82MM Throttle Body + Induction Kit Porsche 996 / 997 - IPDKIT99602
Code: IPDKIT99602
Aluminum Intake Plenum + 82MM Throttle Body + Induction Kit Porsche 996 / 997
Dyno tested power gains with our ECU remap archiving and extra +30Bhp To read more about this power increase Click Here
IPD
Porsche has been controlling engine output by restricting the inlet track for decades. This has been successfully accomplished by utilizing smaller throttle bodies. This simple power control solution has been a very effective way of preventing lower level models from out performing certain flagship models, especially models with prolific racing pedigree. Although the factory engine packages are fantastic performance machines, they are engineered and developed to achieve specific performance numbers that satisfy a target demographic and compete with rival brands. Unfortunately driving enthusiasts who seek an elevated Porsche driving experience require performance levels well outside the target market.
Power improvements will be fully realized once the factory ECU/DME makes all the necessary "adaptation" requirements. This process can be expedited with a series of "hard pulls" or spirited full throttle acceleration runs through the gears. Of course this should only be performed on a closed course circuit.
Induction Kit
Engineered for maximum power and sound. This engineered system eliminates the OEM restrictive airbox and incorporates a high flow cone air filter and sealed fresh air chamber. A cone filter has superior air flow characteristics as compared to flat panel filters. The cone filter better shapes the air as it enters through the filter for smoother straighter more formed air. Next, we have CMC machined a MAF housing to the exact tolerances of the OEM housing for precise MAF reading and NO CHECK ENGINE LIGHTS. In addition, the sealed air chamber sections off the cone air filter from the engine compartment so that it can only draw cool outside air for more power. Finally, the system is injected molded from crosslink polyethylene which has the lowest thermal conductivity rating of any single-layered moldable material available on the market today. This is key in keeping intake temperatures low and increasing power.
Fits:
Porsche 997 Carrera
Porsche 996 Carrera*
(*FOR CARS WITH "ELECTRONIC ACCELERATOR (M620)" NOT FOR EARLY CABLE THROTTLE CARS)
Dyno tested power gains with our ECU remap archiving and extra +30Bhp To read more about this power increase Click Here
IPD
Porsche has been controlling engine output by restricting the inlet track for decades. This has been successfully accomplished by utilizing smaller throttle bodies. This simple power control solution has been a very effective way of preventing lower level models from out performing certain flagship models, especially models with prolific racing pedigree. Although the factory engine packages are fantastic performance machines, they are engineered and developed to achieve specific performance numbers that satisfy a target demographic and compete with rival brands. Unfortunately driving enthusiasts who seek an elevated Porsche driving experience require performance levels well outside the target market.
Power improvements will be fully realized once the factory ECU/DME makes all the necessary "adaptation" requirements. This process can be expedited with a series of "hard pulls" or spirited full throttle acceleration runs through the gears. Of course this should only be performed on a closed course circuit.
Induction Kit
Engineered for maximum power and sound. This engineered system eliminates the OEM restrictive airbox and incorporates a high flow cone air filter and sealed fresh air chamber. A cone filter has superior air flow characteristics as compared to flat panel filters. The cone filter better shapes the air as it enters through the filter for smoother straighter more formed air. Next, we have CMC machined a MAF housing to the exact tolerances of the OEM housing for precise MAF reading and NO CHECK ENGINE LIGHTS. In addition, the sealed air chamber sections off the cone air filter from the engine compartment so that it can only draw cool outside air for more power. Finally, the system is injected molded from crosslink polyethylene which has the lowest thermal conductivity rating of any single-layered moldable material available on the market today. This is key in keeping intake temperatures low and increasing power.
Fits:
Porsche 997 Carrera
Porsche 996 Carrera*
(*FOR CARS WITH "ELECTRONIC ACCELERATOR (M620)" NOT FOR EARLY CABLE THROTTLE CARS)
Product Vehicle Group
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
£1,303.33
Now £1,238.16
In stock 
