Please wait… 
Please wait while we process your order,
do not press the back button… 
Design 911 Design 911 supply Porsche parts, Porsche spares and Porsche accessories, to both retail and to the trade. Our Porsche product and accessory range includes brakes, exhausts, tyres, wheels and Porsche panels and interiors. https://www.design911.com/images/schemaLogo.png https://www.design911.com/images/schemaLogo.png +443456003478 https://www.design911.com Facebook Instagram

Ignition Control Units

Refine by Car Type
Filter by brand
DISPLAYING 1 to 22 (of 22 products)
Ignition kit for CIS injection with 3 pin Gen 6 CDI module. Porsche 911 2.7 / 2.7S
Code: IGNITIONKITCIS
Ignition kit for CIS injection car with 3 pin Gen 6 CDI (HKZ) module. Porsche 911 2.7, 2.7S

permatune

Fits
Porsche 911 2.7 1974 - 1977
Porsche 911 2.7S 1974 - 1977

Perma-Tune Gen 6

Replace those tired and worn ignition components with this Ignition Kit

Contents of Kit
3 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil

The Gen 6 Premium Perma-Tune CDI module makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights.
These LED lights assist in diagnosing both the ignition module and the car. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light which is especially useful for detecting engine misfire.
The LED function lights are mounted in the harness electrical connector and can only be seen with a mirror while the module is powered up.
As an additional feature of the Perma-Tune Premium module, there are three self-resetting overload protectors that protect your Perma-Tune and your car from overload damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part.

Distributor with Harness
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear. Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor, for the 2.0 L and 2.2 L engine. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation.
Simply mount the ignition module to the relay panel where the later model cars had the module mounted and then plug the distributor harness connector into the Perma-Tune module. The power, ground, tachometer and coil connections are made at the existing coil wires. The harness has loop connections that allow joining the wires without having to cut and splice the car harness wires. The Perma-Tune distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look.
The Perma-Tune Bespoke Porsche distributor is an exact fit replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction. Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor. The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance or retard vacuum functions. It just doesn't get any easier than this.

Ignition Coil
The Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a vintage car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKITCIS
91160270700
91160270700
90160250200
911602021
90160250200
911MF126

The product you are viewing cross references to these numbers
About this kit
Kit
Ignition kit for MFI with 3 pin Gen 6 CDI module. Porsche 911 T / E / S
Code: IGNITIONKITMFI
Ignition kit for MFI car with 3 pin Gen 6 CDI (HKZ) module. Porsche 911 2.4 T / E / S and 2.7 MFI

permatune

Fits
Porsche 911 2.4 T 1970 - 1973
Porsche 911 2.4 E 1970 - 1973
Porsche 911 2.4 S 1970 - 1973
Porsche 911 2.7 MFI 1973 - 1974

Perma-Tune Gen 6

Replace those tired and worn ignition components with this Ignition Kit

Contents of Kit
3 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil

The Gen 6 Premium Perma-Tune CDI module makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights.
These LED lights assist in diagnosing both the ignition module and the car. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light which is especially useful for detecting engine misfire.
The LED function lights are mounted in the harness electrical connector and can only be seen with a mirror while the module is powered up.
As an additional feature of the Perma-Tune Premium module, there are three self-resetting overload protectors that protect your Perma-Tune and your car from overload damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part.

Distributor with Harness
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear. Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor, for the 2.0 L and 2.2 L engine. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation.
Simply mount the ignition module to the relay panel where the later model cars had the module mounted and then plug the distributor harness connector into the Perma-Tune module. The power, ground, tachometer and coil connections are made at the existing coil wires. The harness has loop connections that allow joining the wires without having to cut and splice the car harness wires. The Perma-Tune distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look.
The Perma-Tune Bespoke Porsche distributor is an exact fit replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction. Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor. The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance or retard vacuum functions. It just doesn't get any easier than this.

Ignition Coil
The Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a vintage car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKITMFI
91160270700
91160270700
90160250200
911602021
90160250200

The product you are viewing cross references to these numbers
About this kit
Kit
Ignition kit with 3 pin Gen 6 CDI module. Porsche 911 2.0ltr / 2.2ltr
Code: IGNITIONKIT9E
Ignition kit with 3 pin Gen 6 CDI (HKZ) module. Porsche 911 2.0ltr and 2.2Ltr

permatune

Fits
Porsche 911 2.0ltr 1965 - 1969
Porsche 911 2.2ltr 1970 - 1972

Perma-Tune Gen 6

Replace those tired and worn ignition components with this Ignition Kit

Contents of Kit
3 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil

The Gen 6 Premium Perma-Tune CDI module makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights.
These LED lights assist in diagnosing both the ignition module and the car. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light which is especially useful for detecting engine misfire.
The LED function lights are mounted in the harness electrical connector and can only be seen with a mirror while the module is powered up.
As an additional feature of the Perma-Tune Premium module, there are three self-resetting overload protectors that protect your Perma-Tune and your car from overload damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part.

Distributor with Harness
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear. Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor, for the 2.0 L and 2.2 L engine. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation.
Simply mount the ignition module to the relay panel where the later model cars had the module mounted and then plug the distributor harness connector into the Perma-Tune module. The power, ground, tachometer and coil connections are made at the existing coil wires. The harness has loop connections that allow joining the wires without having to cut and splice the car harness wires. The Perma-Tune distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look.
The Perma-Tune Bespoke Porsche distributor is an exact fit replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction. Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor. The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance or retard vacuum functions. It just doesn't get any easier than this.

Ignition Coil
The Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a vintage car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKIT9E
91160270700
90160250200
911602021
90160250200

The product you are viewing cross references to these numbers
About this kit
Kit
Ignition kit with 6 pin basic CDI module. Porsche 911 SC and 911 turbo (USA)
Code: IGNITIONKITSCB
Ignition kit with basic 6 pin CDI (HKZ) module. Porsche 911SC and turbo

permatune

Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)

Perma-Tune Gen 6

Replace those tired and worn ignition components with this Ignition Kit

Contents of Kit
6 Pin CDI Module - Basic
Distributor with Harness
Ignition Coil

CDI Module
The Gen 6 Perma-Tune for the 911SC comes in two models: Premium ignition module and the Basic ignition module. The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day. For the average street car, this may be all that is desired and of course is more affordable than the Premium model. It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.

Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.

Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKITSCB
93060270200
93060270200
930602021DX
930602021DX
90160250200
90160250200

The product you are viewing cross references to these numbers
About this kit
Kit
Ignition kit with 6 pin Gen 5 CDI module. Porsche 911 SC and 911 turbo (USA)
Code: IGNITIONKITSCG5
Ignition kit with 6 pin Gen 5 CDI (HKZ) module. Porsche 911SC and turbo

permatune

Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)

Perma-Tune Gen 5

Replace those tired and worn ignition components with this Ignition Kit

Contents of Kit
6 Pin CDI Module - Gen 5 Version
Distributor with Harness
Ignition Coil

CDI Module
The Generation 5 ignition boxes make diagnostics easier. The controller monitors and runs diagnoses programs automatically and is read by two coloured LED function lights the are viewable from underneath the unit. The diagnoses can also be done via a Bluetooth programming dongle which is available as a separate item.

Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.

Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKITSCG5
93060270200
93060270200
930602021DX
930602021DX
90160250200
90160250200

The product you are viewing cross references to these numbers
About this kit
Kit
Ignition kit with 6 pin Premium CDI module. Porsche 911 SC and turbo (USA)
Code: IGNITIONKITSCP
Ignition kit with Premium 6 pin CDI (HKZ) module. Porsche 911SC and turbo

permatune

Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)

Perma-Tune Gen 6

Replace those tired and worn ignition components with this Ignition Kit

Contents of Kit
6 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil

CDI Module
The Gen 6 Perma-Tune for the 911SC comes in two models:Premium ignition module and the Basic ignition module.
The Premium ignition module features a smooth, matt finish that mimics the patina of the original aluminum die cast part. It provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone. This module comes preprogrammed for the Porsche 911SC so programming changes are optional. The Gen 6 Premium Perma-Tune makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights. These LED lights assist in diagnosing both the vehicle and the ignition module. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light. This LED is especially useful for detecting intermittent engine misfire caused by wiring or distributor problems. The LED function lights are mounted in the harness electrical connector and can only be seen when the module is powered up. There are three self-resetting overload protectors that assist in troubleshooting while protecting your Perma-Tune from damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part. Refer to the Diagnostics section of this web site for more information about the diagnostics system and overload protectors.

Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.

Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKITSCP
93060270200
93060270200
930602021DX
930602021DX
90160250200
90160250200

The product you are viewing cross references to these numbers
About this kit
Kit
3 pin CDI connector housing. Porsche 911 / 914/6
Code: 90160270201/1
3 pin CDI connector housing. 

oematch

Fits:
Porsche 911 - 1965 to 1977
Porsche 914/6

3 pin CDI Connector Housing for Porsche 911.

This is a high quality reproduction part made from PA12 Nylon which is tough, durable, heat and chemical resistant. It is also an excellent insulator.

Please Note
Pins & wiring not included, this is only the empty housing.



Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90160270201
90160270201

The product you are viewing cross references to these numbers
Best Product
3 Pin CDI ignition module. Porsche 911 / 914/6 1965-77 premium version
Code: 91160270700/3
3 Pin CDI (HKZ) ignition module.
Premium version
(Bosch reference 227-200-001)

permatune

New Perma Tune Gen 6

Fits:
Porsche 911 1965-77
Porsche 914/6

Disclaimer: Before fitting this CDI unit please make sure the new PERMA TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.

The Gen 6 Premium Perma-Tune CDI module makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights.
These LED lights assist in diagnosing both the ignition module and the car. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light which is especially useful for detecting engine misfire.
The LED function lights are mounted in the harness electrical connector and can only be seen with a mirror while the module is powered up.
As an additional feature of the Perma-Tune Premium module, there are three self-resetting overload protectors that protect your Perma-Tune and your car from overload damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part.

The Premium ignition module features a die cast housing that has been treated to mimic the patina of the original aluminum die cast distributor and has a range of digital features that the Basic module does not have. The Premium module provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone. The 911906 comes preprogrammed for the Porsche 911 so programming changes are optional. The programmable mechanical advance feature is very handy for restoring a distributor advance curve that has been distorted by worn mechanical parts without having to replace the weights and springs. Scroll down for more complete information about your programming options.

DISTRIBUTOR TRIGGER SIGNAL

The second most common cause of SC engine ignition failure is the ignition trigger circuit.
Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91160270700
91160270700
90160270200
901602702AX
911903
227-200-001
227200001
108540600
227200001
227200002
901602702X
911906

The product you are viewing cross references to these numbers
Best Price
3 pin ignition module CDI box. Porsche 911 / 914/6 1965-77 basic version
Code: 91160270700/2
3 pin Ignition module CDI (HKZ) box
Basic version
(Bosch reference 227-200-001)

permatune

Disclaimer: Before fitting this CDI unit please make sure the new PERMA-TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA-TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.

Perma-Tune Gen 6

Fits:
Porsche 911 1965-77
Porsche 914/6

Take your pick: Basic or Premium

The Gen 6 Perma-Tune comes in two models: the Model Premium ignition module and the Basic ignition module.

The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day. For the average street car, this may be all that is desired and of course is more affordable than the Premium model.
It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.

DISTRIBUTOR TRIGGER SIGNAL

The second most common cause of SC engine ignition failure is the ignition trigger circuit.
Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91160270700
91160270700
90160270200
901602702AX
911903
227-200-001
227200001
108540600
227200001
227200002
901602702X
911706

The product you are viewing cross references to these numbers
Best Price
6 pin CDI connector housing. Porsche 911
Code: 93060270200/5
6 pin CDI connector housing. 

oematch

Fits:
Porsche 911 - 1978 to 1989

6 pin CDI Connector Housing for Porsche 911.

This is a high quality reproduction part made from PA12 Nylon which is tough, durable, heat and chemical resistant. It is also an excellent insulator.

Please Note
Pins & wiring not included, this is only the empty housing.



Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200
93060270200
930602702X
930602702 X

The product you are viewing cross references to these numbers
Best Product
6 Pin CDI ignition module. Porsche 911 / 911 turbo (USA) 1978-89 premium version
Code: 93060270200/3
6 Pin CDI (HKZ) ignition module.
Premium version
(Bosch Ref 0227300004)

permatune

New Perma Tune Gen 6

Disclaimer: Before fitting this CDI unit please make sure the new coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty.

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89 (US cars only)

Take your pick: Basic or Premium

The Gen 6 Perma-Tune for the 911SC comes in two models: the Premium ignition module and the Basic ignition module.

The Premium ignition module features a smooth, matt finish that mimics the patina of the original aluminum die cast part.
It provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone.
This comes preprogrammed for the Porsche 911SC so programming changes are optional. The programmable mechanical advance feature is very handy for restoring a distributor advance curve that has been distorted by worn mechanical parts without having to disassemble and repair the distributor.
The Gen 6 Premium Perma-Tune makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights. These LED lights assist in diagnosing both the vehicle and the ignition module. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light. This LED is especially useful for detecting intermittent engine misfire caused by wiring or distributor problems.
These LED function lights are mounted in the harness electrical connector and can only be seen when the module is powered up. There are three self-resetting overload protectors that assist in troubleshooting while protecting your Perma-Tune from damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part. Refer to the Diagnostics section of this web site for more information about the diagnostics system and overload protectors.

For more information about this product Click Here

DISTRIBUTOR TRIGGER SIGNAL
The second most common cause of SC engine ignition failure is the ignition trigger circuit. Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200
93060270200
0227300004
930602702X
911SC906

The product you are viewing cross references to these numbers
Best Price
6 Pin CDI ignition module. Porsche 911 911 turbo (USA) 1978-89 basic version
Code: 93060270200/4
6 Pin CDI (HKZ) ignition module.
Basic version
(Bosch Ref 0227300004)

permatune

New Perma-Tune Gen 6 Unit

Disclaimer: Before fitting this CDI unit please make sure the new coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty.

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89 (US cars only)

Take your pick: Basic or Premium

The Gen 6 Perma-Tune for the 911SC comes in two models: the Premium ignition module and the Basic ignition module.

The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day.
For the average road car, this may be all that is desired and of course is more affordable than the Premium model.
It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.

For more information about this product Click Here

DISTRIBUTOR TRIGGER SIGNAL
The second most common cause of SC engine ignition failure is the ignition trigger circuit. Since the ignition box is controlled by the magnetic pulse generator located inside the distributor, any disruption in the triggering signal will cause the ignition box to malfunction. Be aware that the connectors can push back in the housing. Pull the rubber boot back to inspect the connection between the box and harness.
Full disassembly and inspection of the distributor is highly recommended due to the intermittent nature of triggering problems. Pay special attention to the distributor trigger shielded cable ( green wire ), magnetic pulse generator magnet and magnetic pulse generator winding connection as these parts are known to fail in combination. An especially common problem is a broken magnet pole. Evidence of arching between the magnetic pulse generator magnet points indicates a defective rotor. In this case replace the rotor, magnetic pulse winding, green wire and ignition box. The Perma-Tune high performance triggering is so accurate that worn out distributor shaft bearings can be detected by the tachometer. This is indicated by the tachometer needle slightly bouncing at idle. Trigger signal problems can cause double triggering which results in a weak ignition spark. Due to the lower triggering resolution of the stock ignition box, some symptoms of trigger signal problems can be more evident after the Perma-Tune is installed. Refer to the vehicle maintenance manual for triggering signal wave form specifications and distributor repair instructions.
To quickly test the triggering circuit without the use of an oscilloscope: Unplug the harness connector from the ignition box. Refer to the 911SC Installation Instructions diagram, connect an Ohm meter between pins 3 and 6 of the harness connector. To prevent the possibility of misdiagnosis, tug on the green triggering signal wire located at the base of the distributor while viewing the meter. The published specification for the magnetic pulse generator is 600 Ohms +- 100. Our experience has shown that a variation of +- 25 Ohm indicates a need to repair defective connections or to replace the magnetic pulse generator windings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200
93060270200
0227300004
930602702X
911SC706

The product you are viewing cross references to these numbers
Best Price
CDI ignition module Bluetooth Programming Dongle Porsche 911 Perma Tune
Code: 90506
CDI ignition module Bluetooth Programming Dongle, fits with Perma Tune 3 pin and 6 Pin Cdi boxes.

permatune

Fits:
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

The new generation ignition boxes make diagnostics easier. The controller monitors and runs diagnoses programs automatically and is read by two coloured LED function lights the are viewable from underneath the unit. The diagnoses can also be done via this Bluetooth programming dongle.

New Perma Tune unit.

For Bluetooth Installation Instruction CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90506
91160270700
90506
93060270200
93060270200

The product you are viewing cross references to these numbers
Best Price
CDI ignition module Programming Cable Porsche 911 / 356 Perma Tune
Code: 90502
Ignition Starter box CDI (HKZ) Bluetooth Programming Cable, fits with Perma Tune 3 pin and 6 Pin Cdi boxes.

permatune

Fits:
Porsche 356 12V
Porsche 911 1974-77
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

The 90502 USB Smart Wire allows you to customize your Perma-Tune Ignition module program. It plugs into the USB port of a computer and then installs itself automatically. It also powers up the module for programming with a single plug without having to connect anything else to the module. The programming software is downloaded from the internet, free, so the module settings can then be changed, saved and organized as text files.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90502
91160270700
90502
93060270200
93060270200

The product you are viewing cross references to these numbers
Best Price
CDI Wiring Harness. Porsche 911 1978-83 / 930 1976-89
Code: CDI911930
Replaces the wiring Harness from the distributor pigtail to the CDI Box. If you need to replace from the ignition distributor to the CDI box then you will also need to add the short Green Wire part number 930.602.907.01 to complete connection.
Best Price
Complete ignition harness for a 3 pin CD1/HK2 box. Porsche 911 1965-73 / 914
Code: 91161205000/1
Complete ignition harness for a 3 pin CD1/HK2 box.
Includes all connector boots, PVC sheathing, high grade automotive wire, flat braided ground cable and contacts per the original specifications. Compatible with cars up to 1973.

oematch

Fits:
Porsche 911 1965-73
Porsche 914/6 1971-75



Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91161205000
91161205000

The product you are viewing cross references to these numbers
Best Product
Ignition Coil. Porsche 911 / 930
Code: 90160250200/3
Ignition Coil. Porsche 911 / 930

permatune

This coil is designed to replace the Marelli BAE202B ignition coil or Bosch 0221121001. It will work with the Porsche Perma-Tune ignition modules. It is intended to look like original equipment and is a high quality coil made in the USA.

Fits:
Porsche 911 1970-83 / 911 SC
Porsche 930 Turbo 3.0L 1975-77
Porsche 930 Turbo 3.3L 1986-89
Porsche 356 12v Only

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90160250200
90160250200
108536105

The product you are viewing cross references to these numbers
Best Price
Ignition Harness for CDI 3 PIN. Porsche 911 1975-77
Code: 91161205100/1
CDI box wiring harness, 1975 to 1977 Three Pin

This is designed to replace your aging and cracked wiring harness that connects the CDI box to the ignition coil and ignition distributor. The harness will plug directly in as we now manufacture the plugs and boots.
This harness is for 1975 to 1977 911 not for Pertonix

Fits:
Porsche 911 1975-77

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91161205100
91161205100

The product you are viewing cross references to these numbers
Best Price
Ignition Harness for CDI 6 PIN. Porsche 911 1978-89
Code: 93061205000
6 Pin CDI Harness

This harness is designed to be a stand alone replacement wiring harness for the 911SC models using the 6 pin CDI system. Until now the only way to replace a damaged ignition harness on the SC models was to replace the entire engine harness. This is very expensive and time consuming to do. We have designed this harness to allow the mechanic to just replace the wiring harness that controls the ignition function of the vehicle. The harness will plug directly into the CDI Box, The Ignition distributor and coil. The only two connections that will require some plug dis-assembly are the 12V ignition connection at the rear fuse panel and the tachometer signal wire at the 14 pin plug connector. Both of these wires come with the correct connectors installed on the wires.

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93061205000
93061205000

The product you are viewing cross references to these numbers
Best Price
Ignition module. Porsche 356 or early 911 12V or 8V
Code: 356906
Ignition module. Porsche 356 or early 911 12 Volt or 8 Volt ignition cars.

permatune

Disclaimer: Before fitting this CDI unit please make sure the new PERMA-TUNE coil is being fitted with it. Do not try to start the car with Blue Bosch coil made in Brazil. This will damage the Perma-Tune CDI box and void the warranty. If CDI unit was not purchased with the PERMA-TUNE coil the warranty will not be respected. Fitting with other brand coils at your own risk.

Bluetooth programmable (Bluetooth Smart Wire required part no 90506)

Brand: Perma Tune
This is an upgrade for the ignition system. Basically it puts the load of the ignition system through the box rather than the distributor. You take the existing wiring and run it through this box and the points then become an earth trigger switch for the box rather than switching the coil.


This Model is the first of a brand new product line for Perma-Tune. We have combined our accumulated knowledge of Porsche ignition over the last 48 years and applied it to the very latest electronics technology to produce a state of the art electronic ignition module that is period correct looking. Made to look like an old school electrical relay, it blends right into the engine bay of a 356 or an early 911.

NO CRIMPS, NO MESS, NO HEADACHES
Plug and play features eliminate the need for wire crimps and complicated wiring diagrams. Wires are cut and stripped, then inserted into the wire bus for a secure, plug in connection without the need for special tools or wire crimps.

Simple, four wire installation. There is no need to interpret complicated wiring diagrams, the terminals are clearly marked so you know exactly where each wire goes.

NO DIALS, NO SWITCHES, NO PROBLEMS
Installation is easy. There are no dials to turn, no switches to set and no chips to plug in. The 356906 Perma-Tune comes to you pre-programmed and ready to be installed on a 356. You can always customise the module later using your wireless device to make secure, reliable configuration changes through the built in Bluetooth connection.

STRONG, YET FORGIVING
The Perma-Tune ignition module features on board diagnostics to help you install the module. The built in strobe light can help you check your ignition timing. It also has self resetting overload protection so there are no fuses to replace.

SMART CONNECTIONS
Use any kind of distributor you have. The Points distributor connection will work with breaker points or any aftermarket distributor.

The tachometer output connection is universal and will work with the stock tachometer or aftermarket electronic tachometer, shift light and RPM switch.

Power connects to 12 Volt or 8 Volt systems. Six Volt converters are not available at this time.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

356906
356906
910905

The product you are viewing cross references to these numbers
Best Price
Ignition Starter box CDI 3 PIN. Porsche 911 1965-77 Classic Retrofit
Code: 91160270700/
Ignition Starter box CDI 3 PIN.
(Bosch reference 227-200-001)


Classic Retrofit replacement CDI+ ignition offers you bespoke modern electronics in a standard looking package. The CDI+ unit requires no modifications to the original wiring harness or vehicle metalwork and is 'plug and play'.

The CDI+ is a direct replacement for the 3 pin and 6 pin Bosch units fitted to Porsche 911's between 1969 and 1983 (and turbo models to ~1988). All CDI+ units have a 48 MHz microprocessor onboard to control ignition timing.

Basic Unit:
The basic unit is a plug and play replacement for the Original Bosch CDI. It will work with the existing distributor without modification and still uses the weights and springs for the advance curve. It is pre-set at the factory (to your specification) and has the following features:
-Hard RPM limiter.
-Soft RPM limiter.
-Double spark at all RPMs
-Shift Light output
-Tacho calibration
-Upgradeable through firmware updates (at one of our specialists)
-The following parameters can be adjusted using the hidden 'jog wheel'.
-Hard RPM limiter.
-Soft RPM limiter.
-Shift light RPM.
-Tacho calibration.
The basic unit can be upgraded to an advanced unit at a later date by one of our specialists.

Advanced Unit:
The advanced unit allows the adjustment/tuning of the ignition advance curve and other features by plugging in a laptop. This can be achieved by 'overlaying' a curve on top of the distributor weights/springs curve or by locking the distributor and replacing the curve completely. Either way, you can unlock the true potential of your engine by adjusting fuelling and having the ignition curve to match.

The CDI+ has all the features of the basic unit but allow more flexibility in adjustment:
-Fully programmable ignition advance curve.
-Hard RPM limiter with adjustable ignition cut schemes
-Soft RPM limiter with adjustable ignition retard
-Launch RPM limiter
-Double spark at all RPMs
-Max RPM tell tale
-Shift Light output
-Clutch pedal input
-Tacho calibration
-Upgradeable through firmware updates

Fits:
Porsche 911 1965-77

For 911-CDI+ Ignition Manual CLICK HERE

For 911-CDI+ Dyno Test Results CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91160270700
91160270700
90160270200
90160270201
901602702AX

The product you are viewing cross references to these numbers
Best Price
Ignition Starter Unit CDI 6 PIN. Porsche 911 1978-89 Classic Retrofit
Code: 93060270200/A
Ignition Starter Unit CDI 6 PIN.
(Bosch Ref 0227300004)

Classic Retrofit replacement CDI+ ignition offers you bespoke modern electronics in a standard looking package. The CDI+ unit requires no modifications to the original wiring harness or vehicle metalwork and is 'plug and play'.

The CDI+ is a direct replacement for the 3 pin and 6 pin Bosch units fitted to Porsche 911's between 1969 and 1983 (and turbo models to ~1988). All CDI+ units have a 48 MHz microprocessor onboard to control ignition timing.

Advanced Unit:
The advanced unit allows the adjustment/tuning of the ignition advance curve and other features by plugging in a laptop. This can be achieved by 'overlaying' a curve on top of the distributor weights/springs curve or by locking the distributor and replacing the curve completely. Either way, you can unlock the true potential of your engine by adjusting fuelling and having the ignition curve to match.

The CDI+ has all the features of the basic unit but allow more flexibility in adjustment:
-Fully programmable ignition advance curve.
-Hard RPM limiter with adjustable ignition cut schemes
-Soft RPM limiter with adjustable ignition retard
-Launch RPM limiter
-Double spark at all RPMs
-Max RPM tell tale
-Shift Light output
-Clutch pedal input
-Tacho calibration
-Upgradeable through firmware updates

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

For 911-CDI+ Ignition Manual CLICK HERE

For 911-CDI+ Dyno Test Results CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200
93060270200
930602702 X
930602702X

The product you are viewing cross references to these numbers
Best Price
DISPLAYING 1 to 22 (of 22 products)
Also found on these pages
You may also like
Popular Models