Side section / Sub frame

HD Rear subframe bushing. racing version
Complete set (4 pcs). 2 sets needed for one car.



Fits:
Porsche 993 1995-98 all models

Increase rear end stability and extend the life of your alignment with High Density subframe mounts. Factory units can cause rear ends to become more 'twitchy' and nervous, especially under high suspension loads, especially as they begin to fail. These bushings are not only responsible for holding the entire rear subframe to the shell, but for locating it in relation to the body and other suspension components. This means that even if they have not totally fallen apart the stock, soft mounts can often allow the entire rear suspension to shift and realign itself and as a result your entire car. Made from heavy duty high durometer rubber which features a 25% increase in stiffness over OE units, our High Density bushing kit includes the aluminum inner core and outer casement making them a plug and play solution for your 993. Enjoy a more planted rear end and stop living at the alignment shop with this full rear subframe kit.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99333105100

The product you are viewing cross references to these numbers

Adjutable rear axle solid bushing set.
This set allows you to lower the suspension -25mm from the original height.



Fits:
Porsche 993

Material:
6082-T6 Aluminium

Click 'Zoom in' for large parts diagram.
Outlined in green on diagram.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

9P-0193

The product you are viewing cross references to these numbers

HD Rear subframe bushing. street version
Complete set (4 pcs). 2 sets needed for one car.



Fits:
Porsche 993 1995-98 all models

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99333105100

The product you are viewing cross references to these numbers

Rear suspension side section bushing kit.
4 pcs in kit - 2 kits required per car



Fits
Porsche 993 - All 1994 - 1998

Replaces the rubber bushings on the rear 993 side panels.

Stock hardness – Restores performance and ride quality to original.

Sport-hardness – Firmer rubber more precisely locates suspension members under load, without the noise and vibration associated with solid metal alternatives.

Each side panel has 4 rubber bushings, for a total of 8 bushings per car.
Each kit includes 4 bushings, order 2 kits per car

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

229001

The product you are viewing cross references to these numbers

Rear Suspension Side Section.


Fits:
Porsche 993 1995-98

Click 'Zoom in' for large parts diagram.
Diagram ref no 2

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99333105

The product you are viewing cross references to these numbers

Rennline solid rear subframe kit and tilt kit.



Fits:
Porsche 993

Factory rubber suspension mounts have a lot of flexibility and cannot withstand the extreme loads applied to them during performance driving conditions. When these mounts flex, all of the suspension geometry changes making the car unstable and unpredictable. A very popular suspension upgrade is to replace these bushings with solid mounts like the ones found on the factory race cars. These kits are machined out of billet aluminum and come with the required hardware to install.

This kit can be purchased as a Solid Sub Frame Mount Kit or as a Solid Sub Frame/Tilt Kit as found on the factory 993GT2 race cars.

For Fitting Instruction please CLICK HERE

Note: Pictures may not show actual product.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SB656676

The product you are viewing cross references to these numbers

Solid Rear Subframe Bushing Kit.


Fits:
Porsche 993

Factory rubber suspension mounts have a lot of flexibility and cannot withstand the extreme loads applied to them during performance driving conditions. When these mounts flex, all of the suspension geometry changes making the car unstable and unpredictable. A very popular suspension upgrade is to replace these bushings with solid mounts like the ones found on the factory race cars. These kits are machined out of billet aluminium and come with the required hardware to install.


Note: Pictures may not show actual product.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SB5876

The product you are viewing cross references to these numbers

Solid subframe bushing set. Precision Handling - REAR
1 kit required per car.



Fits:
Porsche 993 1995-98

Stock rubber bushings compress and deform under heavy cornering, braking, and acceleration loads. The compliant rubber bushings allow the entire rear subframe shift about relative to the chassis. Rear camber and toe settings wander along with the subframe making the car less predictable, less stable in turns.

Our solid bushings replace the compliant rubber and do not deform under cornering loads, keeping the subframe in position and alignment true even under heavy cornering loads. The car becomes more predictable and easier to drive fast.

Corrects Geometry
Raises the subframe by 10mm to improve geometry and camber curve on lowered cars.

Build Quality
Each bushing consists of two pieces… identical upper and lower pucks.

Each piece is precision machined from high-strength aluminium with an anodized finish for protection.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2290037

The product you are viewing cross references to these numbers