Cardan Shaft / Prop Shaft
Fits:
Porsche 924 Turbo / GT 1976-85
Porsche 924 S 1986-88
Porsche 944 1982-91
Porsche 928 1978-95
Porsche 964 1989-94
Click 'Zoom in' for large parts diagram.
Diagram ref no 4
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
92242105103
The product you are viewing cross references to these numbers
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 924 Turbo 2.0L 1979-81
- Porsche 924 Turbo 2.0L 1982-84
- Porsche 924 Carrera GT 2.0L 1981
- Porsche 924 Carrera GTS 2.0L 1982
- Porsche 924S 2.5L 1986-87
- Porsche 924S 2.5L 1988
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988>>
- Porsche 928 4.5L 1978-82
- Porsche 928S 4.7L 1981-83
- Porsche 928S2 4.7L 1984-86
- Porsche 928S4 5.0L 1987-92
- Porsche 928GT 5.0L 1989-91
- Porsche 928GTS 5.4L 1992-95
If your Porsche Cayenne's Drive Shaft Cardan Shaft / Prop Shaft is not operating efficiently, it will let you know immediately. Drive Shaft noises are usually caused by worn center support dampener, or a faulty center support bearing. Drive shaft noises and possible causes are as follows:
- A clunking or thumping sound, when going from acceleration to deceleration or deceleration to acceleration, may be caused by worn center support bearing dampener or diaphragm. A broken or worn center support bearing dampener will allow for the shaft to move up and down with changes in drive line torque. This movement will cause a loud clunking or thumping sound and make for a very uncomfortable ride. A broken center support bearing dampener is one of the most common failures on the Cayenne drive shaft.
- A whining sound from the drive shaft is sometimes caused by a dry, worn center support bearing. Since this bearing makes complete revolutions, it will make a different sound than a bad center support bearing dampener. A high-pitched, more constant whine will usually come from a faulty, broken or worn center support bearing.
- Grinding and squeaking from the drive shaft or prop shaft is frequently caused by worn C.V. joint. The joints become dry, causing the rollers to wear. The un-lubricated, damaged rollers then produce a grinding or squeaking sound, as they operate on the scored cap and cross surfaces.
- Clutch Kits
- Clutch Kits - High Performance
- Clutch Friction Plate
- Clutch Release Bearings
- Clutch Cables & Parts
- Clutch Guide Tube
- Clutch Forks & Levers
- Clutch Bolts
- Driveshafts & Parts
- Gearbox Parts
- Gasket Sets / Gaskets / Seals / Lock Nuts
- Gearshift Control Parts
- Flywheel / Torque
- CV Joints Kits
- CV Boots and Kits
- Gearbox Oil
- Gearbox Sump / Oil Pan
- Rear Differential
- Motor Sport Parts