TEXTAR Brakes
Boiling point brake fluid testing is the only test method approved by brake & brake fluid manufacturers
- Increase service revenue & road safety
- Accurate, reliable & repeatable results
- Operates off the vehicles own 12 volt battery
- Measures up to 320°, suitable for use on all grades of brake fluid including racing fluids
- Multilanguage: English, German, French, Spanish, Italian
Find out about Textar product verification here
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here
Brake fluid DOT 4 LV (Low Viscosity) Textar.
Textar DOT 4 LV (Low Viscosity) is especially recommended for use in hydraulic brake and clutch systems of vehicles fitted with ESP, ABS and ASR with a high boiling point and outstanding performance at very low temperatures.
DOT 4 LV (Low Viscosity)
Dry Boiling Point ≥ 260° C
Wet Boiling Point ≥ 165° C
Viscosity at -40C < 750 mm2 /s
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut. <
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95002
The product you are viewing cross references to these numbers
Porsche Cayenne (955) V8 4.5L S MKI
Porsche Cayenne (955) V8 4.5L Turbo MKI
Porsche Cayenne (957) V8 4.8L S/GTS MKII
Porsche Cayenne (957) V8 4.8L TURBO MKII
* For cars with 19" wheel and silver or red calipers
* option code: I1LL or I1LM
Sold as set of 4 pads for one axle.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95535193916TEX
The product you are viewing cross references to these numbers
- Porsche Cayenne S 4.5L V8 2003>>
- Porsche Cayenne Turbo 4.5L 2003>>
- Porsche Cayenne S/GTS 4.8L 2007>>
- Porsche Cayenne Turbo / Turbo S 4.8L 2007>>
Porsche (955) Cayenne 3.2L V6 MKI FRONT
Porsche (957) Cayenne 3.6L V6 MKII FRONT
Porsche Cayenne (957) 3.0L DIESEL MKII FRONT
*For cars with 430mm/17" disc and Black calipers
*option code: I1LK
Sold as set of 4 pads for one axle.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95535193908TEX
The product you are viewing cross references to these numbers
- Porsche Cayenne 3.2L V6 2003>>
- Porsche Cayenne 3.0L Diesel 2007>>
- Porsche Cayenne 3.6L 2007>>
Porsche Cayenne (955) V8 4.5L Turbo S MKI
Porsche Cayenne (957) V8 4.8L Turbo S MKII
* For cars with 482mm/19" disc brake disc, red calipers.
* Option Code: I1LH
Sold as set of 4 pads for one axle.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95535193952TEX
The product you are viewing cross references to these numbers
- Porsche Cayenne Turbo S 4.5L 2006>>
- Porsche Cayenne Turbo / Turbo S 4.8L 2007>>
Porsche Cayenne (955) V6 MKI REAR
Porsche Cayenne (955) S MKI REAR
Porsche Cayenne (955) Turbo MKI REAR
Porsche Cayenne (957) 3.6L V6 MKII REAR
Porsche Cayenne (957) 4.8L S/GTS MKII REAR
Porsche Cayenne (957) 3.0L DIESEL MKII REAR
Sold as set of 4 pads for one axle.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95535293906TEX
The product you are viewing cross references to these numbers
- Porsche Cayenne 3.2L V6 2003>>
- Porsche Cayenne S 4.5L V8 2003>>
- Porsche Cayenne Turbo 4.5L 2003>>
- Porsche Cayenne 3.0L Diesel 2007>>
- Porsche Cayenne 3.6L 2007>>
- Porsche Cayenne S/GTS 4.8L 2007>>
Porsche Cayenne (955) V8 4.5L Turbo S
Porsche Cayenne (957) V8 4.8L Turbo
* For cars with 457mm brake disc, red calipers
* Option Code I1KU
Sold as set of 4 pads for one axle.
Find out about Textar product verification here
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
95535293950TEX
The product you are viewing cross references to these numbers
- Porsche Cayenne Turbo S 4.5L 2006>>
- Porsche Cayenne Turbo / Turbo S 4.8L 2007>>
For brake systems and is highly temperature-resistant (up to 1,000°C).
Available in 75ml tube and 5ml sachet
The advantages of Cera Tec:
• Non-conductive and contains no solids
• Suitable for ABS
• Facilitates brake installation
• Reduces brake squealing
• Protects against scoring and corrosion
• Free of copper and acids
• Pressure-resistant / high viscosity
Cera Tec is also suitable for lubricating:• Disc- and drum-brake systems
• Compressors
• Centralised lubrication systems
• Axle bearings
• Chains
• Seat rails
• Sunroof tracks
• Battery terminals
Application:
Apply a thin layer of Cera Tec on the marked sections
Find out about Textar product verification here
Hydra tec lubricant for maintenance work and protection Textar
Available in 75ml Tube or 5ml Sachet
The Advantages of Hydra Tec:
- Facilitates the installation of hydraulic brake components
- Tested compatibility with commercially available braking fluids (DOT3, DOT4, DOT4LV, DOT5.1)
- Free of mineral oils and compatible with EPDM rubber
- In addition, running surfaces are protected against corrosion
Hydra Tec is suitable for lubricating:
- Cylinder running surfaces
- Pistons
- Sealing elements
Application:
Apply a thin layer of Hydra Tec on the marked sections.
Note:
Hydra Tec should be applied thinly and evenly.
Never use mineral oils or greases as substitutes.
Do not apply the product on friction surfaces of brake pads or brake discs.
Find out about Textar product verification here
- Brake Pads & Disc Package
- Brake Disc Standard
- Brake Pads Standard
- SPORTS Brake Disc
- Brembo Standard brakes
- Brembo Racing brakes
- PAGID Racing Brakes
- Zimmermann Brakes
- Performance Friction Brakes
- EBC Brakes
- Black Diamond Performance Brakes
- O-Brake Brake Discs
- Rotinger Graphite Line
- Replacement for Ceramic Disc
- Brake Pad Wear Sensors
- Brake Pad Anti-vibration shims
- Caliper Bolts / Disc Screws
- Pin Kit and Guide Plates
- Performance Brake Hoses
- Standard Brake Hoses
- Caliper and Brake Lines
- Brake Calipers
- Brake Caliper Upgrades
- HandBrake Shoes
- HandBrake Cables
- Brake Disc Cover Plates
- ABS | Speed Sensors
- Caliper Seals |Pistons
- Brake Servo | Booster
- Brake Master Cylinder
- Brake Fluid Reservoir
- Brake Fluid
- Build Your Own Brake Kit