Roll Cages

Roll cage 6 point bolt in with single door bars.
For cars without sunroof



MSA/FIA homologated. Certificate 1100 available from MSA

Fits
Porsche 964 Carrera 2 / Carrera 4 - 1989 to 1994
Porsche 964 RS- 1992 to 1993

6 point bolt-in roll cage for single door bars.
This clears normal trim and dashboard and mounts to the floor and rear wheel arches. This allows use of inertia reel seatbelts.

Rear roll cage section is available with different options.
For vehicles WITHOUT sunroof

Build the roll cage to your individual specification using the rear cage and door bar options available below.

For Single Door Bars
• Front cage (Must be used with the front and rear cage)
• Rear cage, single fixed diagonal (May be used without the front cage)
• Rear cage, single fixed diagonal and harness bar (May be used without the front cage)
• Rear cage, cross diagonal and harness bar
(May be used without the front cage)
• Single door bar N/S (left)
• Single door bar O/S (right)
• Finished roll cage supplied with black powder coat finish

Roll cage 6 point bolt in with single door bars.
For cars with sunroof



Not for Competition Use

Fits
Porsche 964 Carrera 2 / Carrera 4 - 1989 to 1994
Porsche 964 RS- 1992 to 1993

6 point bolt-in roll cage for single door bars.
This clears normal trim and dashboard and mounts to the floor and rear wheel arches. This allows use of inertia reel seatbelts.

Rear roll cage section is available with different options.
For vehicles WITH sunroof

Build the roll cage to your individual specification using the rear cage and door bar options available below.

For Single Door Bars
• Front cage (Must be used with the front and rear cage)
• Rear cage, single fixed diagonal (May be used without the front cage)
• Rear cage, single fixed diagonal and harness bar (May be used without the front cage)
• Rear cage, cross diagonal and harness bar
(May be used without the front cage)
• Single door bar N/S (left)
• Single door bar O/S (right)
• Finished roll cage supplied with black powder coat finish

Bolt in roll cage for Porsche 911 models, The roll bar is a bolt in unit with no welding required, the installation hardware is also included. The roll cage is available with or without a centre harness bar.

Fits:
Porsche 964 1989-94

Each roll cage is made to order and powder coated in a RAL colour. You can specify a RAL colour when ordering.
Delivery time is approx. 8 weeks. If you order specific colour which is uncommon the delivery time might be longer.
Standard colours: Black (RAL 9005), Red (RAL 3000 or RAL 3020), white (RAL 9016) or Yellow (RAL 1003 or RAL 1023)

Please visit http://www.ralcolor.com/ and let us know your desired colour.

It mounts on the original mounting points for the security belts with the mounting kit that is included with the rollbar.
So there is no cutting or welding required to the body.

Installation guide?

• Take the seats out
• Loosen the bolts of the mounting points for the security belts
• Lift the rollbar (only with 2 people to prevent damage to any surface)
• Put the roll bar inside the interior
• Mount the rollbar using the mounting kit and mount the security belts back in place BUT do not bolt it fixed yet
• Mount the separate pieces of the rollbar using the stamped guidance pins (like numbers on a tent pole) which piece needs to go where (in the rollbar and the loose pieces)
• Bolt it then fixed to the floor
• Mount the seats
• Take the car for a drive to hear for rattles and see if it needs extra torque on the fixing
• Enjoy!

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

P964RB

The product you are viewing cross references to these numbers