Brey-Krause Harness Mounting

Brey Krause PAIR of Outside Lap Belt Mounts.

Fits:
Porsche 911 All models
Porsche 986/987/981 Boxster all models
Porsche 987/981 Cayman all models

Material: Tig welded, type 304, stainless steel.
Finish: Satin finish stainless.
Weight: 6oz.
Models: All Porsche sports cars.
Installation: Secures snap-in lap belts to outside seat belt mounting point.
Miscellaneous: Allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats. Use part R-9001 for inside belt mount.

For Installation instructions please CLICK HERE

Brey Krause PAIR of Short Inside Lap Belt Mounts.



Fits:
Porsche 911 All models
Porsche 986/987/981 Boxster all models
Porsche 987/981 Cayman all models

These brackets were intended for seat applications where the standard Brey-Krause tunnel-side lap belt mount (R-9001) is too long.

Material: Tig welded, type 304, stainless steel.
Finish: Satin Finish Stainless
Weight: 5oz.
Models: All 911, Boxster and Cayman models
Installation: Secures snap-in lap belts to factory tunnel side (inside) seat belt mounting point.
Miscellaneous: Recommended for extra-low seating applications where the R-9001 sits excessively high. One pair will work for both seats.
Note: Part# R-9002 hardware kit is required for installation in (1985-1989) model Porsches. Use part R-9003 for outside belt mount.

For Installation instructions please CLICK HERE

Brey Krause Clip-In Lap Belt Mounting Kit for OEM Sliders.



Fits:
Porsche 991 / 981 / 997 and 987 models with OEM manual sliders

Material: Tig welded, type 304, stainless steel.
Finish: Satin Finish Stainless
Weight: 5oz.
Models: All 991, 981, 997, and 987 models with OEM manual sliders.
Installation: Secures clip-in lap belts to factory tunnel side (inside) seat belt mounting point on Porsche OEM 991, 981, 997, 987 manual sliders.

For Installation instructions please CLICK HERE

Brey Krause Harness Mount in powder coated black. For Porsche 991 2011>> COUPE ONLY

The Porsche 991 harness mount bar has been tested and certified by an independent lab to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev.MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements.

The 991 harness mount bar properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G loads of cornering and braking. Our bars are easy to install and remove, use only existing holes and mounting points, and will not damage the car in any way.

Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. A mount really can't be relied on unless it has been tested to support the loads required by the National Highway Traffic Safety Administration.

The Brey-Krause Harness Mount supported the loads specified by the National Highway Traffic Safety Admin. DOT for upper torso restraints in all automobiles. Tensile tests performed by an independent lab.

Material: Type 304, stainless steel
Finish: Powdercoated in durable black wrinkle-finish
Weight: 16 lbs
Models: 991 & 992 (Targa models must use R-1033 down tubes)
Installation: Bar attaches to seat belt mounts & seat track hardware.
Miscellaneous: Bar is designed to allow enough seat travel for tall drivers. Includes provisions for Seat Back Brace.

Accessories:

• Replacement Hardware:
• Seat Back Brace: R-9019 & R-9020
• Targa conversion down tubes: R-1033

Brey Krause PAIR of Long Inside Lap Belt Mounts.



Fits:
Porsche 911 All models
Porsche 986/987/981 Boxster all models
Porsche 987/981 Cayman all models

Material: Tig welded, type 304, stainless steel.
Finish: Satin Finish Stainless
Weight: 6oz.
Models: All 911, Boxster and Cayman models
Installation: Secures snap-in lap belts to factory tunnel side (inside) seat belt mounting point.
Miscellaneous: Allows user to remove and install belts in seconds. Will not interfere with factory seat belt.

For Installation instructions please CLICK HERE

Brey krause sub strap mount for adjustable BK mount system 
for seats 425mm or wider at the front mounting points

Fits:
Porsche 991 / 981 / 997 and 987 models with R-9052 Side Mounts

Material: 304 series stainless steel steel tubing
Finish: brushed stainless finish
Weight: 2 lbs.
Models: Mounts to all Brey Krause variable width side mounts

Installation: for seats 425mm or wider at the front mount points

Related Parts:
R-9052 Side Mounts For OEM 991,981,997,987 Sliders
R-9006 Clip-In Inside Lap Belt Mounts
R-9003 Clip-In Outside Lap Belt Mounts

Brey Krause Sub Strap Mount for BK Side Mount Systems. For Mounting a Sub Strap to R-925X Series & R-9052 Side Mounts.
for seats up to 426mm wide at the front mount points.



Fits:
Porsche 991 / 981 / 997 and 987 models with R-9052 Side Mounts

Material: 304 series stainless steel steel tubing
Finish: brushed stainless finish
Weight: 2 lbs.
Models: R-9052 Side Mounts
Installation: R-9052 Porsche 991, 981, 997, 987 Side Mounts integrated mounting points.
Miscellaneous: For seats up to 426mm wide at the front mount points. For seats over 425mm use the R-9258 sub strap mount.

For Installation instructions please CLICK HERE

Related Parts:
Porsche
R-9052 Side Mounts For OEM 991,981,997,987 Sliders
R-9006 Clip-In Inside Lap Belt Mounts
R-9003 Clip-In Outside Lap Belt Mounts