Control Arms Rear

Adjustable lower control arms (lower wishbone)



Fits
Porsche 986 Boxster - Front and Rear
Porsche 996, 997 - Front and Rear
Porsche 991 - Front Only
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 981 Boxster and Cayman - Front and Rear
Porsche 718 Boxster and Cayman - Front and Rear

Set of 2 x Adjustable lower control arms - 1 pair, required per axle

Elephant Racing adjustable lower control arms provide the camber, caster and precision you need. Length adjustable similar to the factory GT3 control arms, but without the need for shims.

Quick and Easy Adjustments – No need to keep a stock of shims on hand, length is easily adjusted by rotating the center hex head. Rotate clockwise to expand or counter-clockwise to contract the arm length.Adjustments can be made within minutes. No shims to mess with. Perfect setup to make quick changes for the track.

Widen Track – Use in combination with our camber plates on the front, or our adjustable length arms upper control arms on the rear to widen the track. This allows you to achieve a wider track without altering the scrub radius as happens when using wheel spacers.

Heim Joint – Our spherical bearings eliminate the deflection associated with rubber bushings. These bearings maintain stable suspension alignment, and improve feedback.

Fully Weather Sealed – Proper boots at both the ball joint and heim joint ends to keep water and contaminants out for extended life. These arms are suitable for extended road and track use.

Camber Adjustment – Extended range of adjustment lets you achieve aggressive camber. Or you can dial it back to get a factory street alignment on lowered cars.

Caster Adjustment – Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms to correct for un-intended caster change that is caused by the extended arms. Rotate the center puck and bolt down to secure the setting.

The arms are fully rebuildable with replaceable heim and ball joints.

On 996, 997, & 991 Cars:
Center puck can be also used as a wheelbase adjuster on the rear to draw the wheels back to improve weight distribution. It is a great tuning aid for adjusting out understeer

Litronic Bracket – This bracket is required for cars that are originally equipped with the litronic headlights. This adapter bracket attaches to the headlight angle sensor.


Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180001

The product you are viewing cross references to these numbers

BBi Autosport adjustable rear toe kit



Fits
Porsche 981 Boxster
Porsche 981 Cayman

Features :

•   Provides additional rear toe adjustment
•   OEM link is non-adjustable and eccentric bolt provides limited adjustment range, causing excessive tire wear and handling issues.
•   Helps maintain proper rear end suspension geometry
•   Fits rear axle
•   Each Kit Includes Pair of 2 Links

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

BBITOE981

The product you are viewing cross references to these numbers

Track control arms with adjustable bushings.



Fitted with Black 95A material for both bushes for ultimate performance and is supplied with an offset outer sleeve and CNC machined inner sleeve to allow for on-car adjustment of both caster and camber, for quick and easy optimisation of your wheel alignment.  (tools or spanner not included)  These arm features suspension geometry tuning, with a caster increase of up to 0.4° and camber adjustment of +/- 0.75°

OEM Part Number: 98133105301, 99733104180, 99634105319

Fits:

FRONT
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR
Porsche 997 GT2, GT3 & GT3RS
Porsche 997 incl. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)

Please note: you will need 997 front fork arms to accommodate the adjustable bushes as they are wider than standard bush. 
When you add this item to the basket you will be prompted with mandatory product you will need to add as well.

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

Please click 'Zoom in' to view the diagram (No 21)

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3602409961G

The product you are viewing cross references to these numbers

GT3 ERX Inner lower control arm (LCA), Rubber Bushing Module.



Fits:
Porsche 996, 997, 991, 992 W/ GT3 Style Control Arms (Front/Rear),
Porsche Boxster, Cayman 1999>> W/ GT3 Style Control Arms (Front Only)

Elephant Racing has developed GT3 type inner lower control arms.
These are readily available and dimensionally identical to the factory parts. They can be mix-matched with the factory type inner/outer lower control arm and shims.
The Elephant Racing inner arm is offered in two flavors, GT3 Street Inner Lower Control Arm and GT3 Cup Inner Lower Control Arm. GT3 street is equipped with a rubber bushed central bushing and the GT3 Cup is equipped with a solid caster adjustable central bushing.
Our GT3 Street Inner Lower Control Arm has sport-hardness rubber bushings to provide upgraded control and driver feedback while still offering good road noise isolation.
Our GT3 Cup Inner Lower Control Arms uses weather sealed spherical bearings. These deliver superior precision, control, and performance. They will transmit a bit more road noise than rubber bushings.

These can be paired with a choice of GT3 outer control lower arms:
– Elephant Racing GT3 Street Outer Lower Control Arms
– Elephant Racing GT3 Cup Outer Lower Control Arms
– Factory GT3 Street Outer Lower Control Arms

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180039

The product you are viewing cross references to these numbers

Lower control arm eccentric monoballs.
1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 - Front and Rear
Porsche 718 - Front and Rear
Porsche 991 - Front Only

Our Eccentric Control Arm Monoball Cartridges replace inner rubber bushings with spherical bearings, providing low friction and precisely holding camber settings.
The eccentric design allows increasing or decreasing camber, as needed.

Increasing Camber

Position the eccentric to maximize Lower Wishbone length, adding about .86 degree of negative camber on the 996/997 rear suspension, about .36 degree of negative camber on the Boxster rear suspension, and .39 degrees on the 996/997/Boxster front suspension.
Cost effective for cars that just want extra camber. For even more camber and ease of adjustment, see our GT3 type fully adjustable control arms.

Decreasing Camber

Position the eccentric to minimize Lower Wishbone length. Perfect for lowered cars that have too much negative camber and want to get back to factory camber settings to minimize tire wear on the street. Makes rear camber about .86 degrees more positive & front camber about .39 degrees positive for 996/997 while Boxsters will get about .39 degrees positive front and .36 degrees positive rear.



Made from hardened steel, plated and weather-sealed, these bearings are made to last. Fits the front or rear stock and GT3 type control arms.

Sized to fit factory original control arms. Not compatible with some aftermarket replacement control arms that use a larger non-stock size bushing.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2260006

The product you are viewing cross references to these numbers

RSS Rear adjustable toe/bump steer link REAR
SET OF 2

Replacement for 98133104501, 98133104502



Fits:
Porsche 981 Boxster / Boxster S
Porsche 981 Cayman / Cayman S

The RSS Adjustable Rear Toe Steer Kit is designed for Porsche models that have been lowered. This kit will help minimize the suspension geometry change in the REAR of the vehicle. Allows for toe adjustment at the toe steer arm giving the ability to make adjustments independent of the factory eccentric bolts which may not offer sufficient adjustment. Allows for bump steer adjustment. Greatly improves handling and feedback. Eliminates rubber bushing deflection. For off road use only.

The links are sold as a pair for the rear of the car.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

301

The product you are viewing cross references to these numbers

RSS XL TARMAC SERIES XL 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Rear Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits:
FOR REAR AXLE PORSCHE 986, 996, 997, 987, 981/982/718

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.
*** Note: 981 and 991 Models may require additional Front Litronic or Torque Vector Sensor Brackets.

RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers If you need assistance in identifying your suspension type please contact us. For specific fitment information refer to the "Chassis Fitment Guide and Lower Control Arm Fitment Notes" (See Images Below).

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS:
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength
steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS.

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS

RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

374

The product you are viewing cross references to these numbers

REAR NON-ADJUSTABLE THRUST ARM BUSHING KIT. Rear Axle. Ideal for castor/length adjustable style thrust arms from other brands. for Porsche 986/996/997/981/982/718

SET OF 4. REAR AXLE ONLY

Brand:

The RSS Non-Adjustable Thrust Arm Bushing Kit will improve handling and response in suspension systems. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.

AVAILABLE FOR ALL PORSCHE® 986, 987, 996, 997, 981 MODELS INCLUDING TURBO & GT3 FOR NON-HYDRAULIC APPLICATIONS ONLY FOR HYDRAULIC APPLICATIONS.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

334

The product you are viewing cross references to these numbers

Rear Toe Link Locking Plate Kit.
SET OF 2



Fits:
Porsche 996 C2, C4, C4S, Turbo, GT2, GT3
Porsche 997 C2, C2S, C4, C4S, Turbo, GT2, GT3
Porsche 986 Boxster / Boxster S
Porsche 987 Boxster / Boxster S
Porsche 987 Cayman / Cayman S
Porsche 981 Boxster / Boxster S
Porsche 981 Cayman / Cayman S / Cayman GT4
Porsche 991 C2, C2S, C4, C4S, Turbo, GT2, GT3
Porsche 982 (718) Boxster / Boxster S
Porsche 982 (718) Cayman / Cayman S

The optional RSS Locking Plate Kit is designed for use with RSS Adjustable Rear Toe/Bump Steer Kit (Part# 312).

This kit replaces the factory eccentric bolt which can come loose under racing and/or aggressive driving conditions.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

333

The product you are viewing cross references to these numbers

Spherical bearing inner GT3 monoballs for factory GT3 lower arm.

1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 - Front and Rear
Porsche 718 - Front and Rear
Porsche 991 - Front Only
Porsche 992 - Front Only
* Not For '12+ 991, 992 GT3/GT4

GT3 Street Inner Spherical Bearing Module

Unlike the factory rubber bushed GT3 inner control arms, our spherical bearings do not deflect under load.
They are fully weather sealed to keep out water and grit for extended life.

• Use in combination with factory GT3 street type control arm only
• Does not fit 991 GT3 or GT4 arms
• Easy Bolt-On
• Weather-sealed
• Sold as pair
• Front and Rear for 996, 997, 986, 987, 981, 718
• Front only on 991

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180030

The product you are viewing cross references to these numbers

Track Control Arm and Bush Kit Adjustable uses our Black 95A material for both bushes for ultimate performance and is supplied with an offset outer sleeve and CNC machined inner sleeve with spanner to allow for on-car adjustment of both caster and camber, for quick and easy optimisation of your wheel alignment.

PACK OF 2

This arm features suspension geometry tuning, with a caster increase of up to 0.4° and camber adjustment of +/- 0.75°

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 GT2, GT3 & GT3RS
Porsche 997 inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Short Adjustable Stainless Steel Sleeves
1 x C45 Spanner
2 x Stainless Steel Washers

Pre-assembled parts:
2 x Cast Aluminium Track Control Arms
2 x Outer Bushes
2 x Inner Bushes
2 x Long Adjustable Stainless Steel Sleeves
2 x Ball Joint Nuts

Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

PF57K-1001G

The product you are viewing cross references to these numbers

Track control arm and bush kit uses a Black 95A inner bush and Purple 80A outer bush, providing a direct replacement alternative to worn OEM parts.

PACK OF 2

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 ALL inc GT2, GT3 & GT3RS
Porsche 997 MK2 ALL inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Cast Aluminium Track Control Arms
Pre-assembled parts:
2 x Outer Bushes
2 x Inner Bushes
2 x Short Stainless Steel Sleeves
2 x Long Stainless Steel Sleeves
2 x Ball Joint Nuts


Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

PF57K-1001

The product you are viewing cross references to these numbers

Track control arm and bush kit Black series

PACK OF 2

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 GT2, GT3 & GT3RS
Porsche 997 inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Cast Aluminium Track Control Arms
Pre-assembled parts:
2 x Outer Bushes
2 x Inner Bushes
2 x Short Stainless Steel Sleeves
2 x Long Stainless Steel Sleeves
2 x Ball Joint Nuts

Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

PF57K-1001BLK

The product you are viewing cross references to these numbers