Manifold / Headers

Equal length exhaust manifold with catalytic converter. 
Sold as a pair - left and right



Fits:
Porsche 718 Boxster GTS 4.0ltr- 2017 Onwards
Porsche 718 Boxster Spyder 4.0ltr - 2017 Onwards

Porsche 718 Cayman GTS 4.0ltr  - 2017 Onwards
Porsche 718 Cayman GT4 4.0ltr - 2017 Onwards

Made from SS304L lightweight stainless steel these exhaust manifolds offer reduced back pressure with higher flow

• Performance gains of 15hp minimum and 20nm
• Improved throttle response
• Improved exhaust note with no drone, resonation or vibration
• Direct fit no remap required but recommended
• No CEL
• Heat shielded to reduce radiant heat and speeds up exhaust gas velocity

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

982254018F

The product you are viewing cross references to these numbers

These titanium components are resistant to rust and corrosion, which can be a common issue with traditional steel studs and nuts. This corrosion resistance ensures that the studs and nuts maintain their integrity, allowing for easy removal and installation when necessary. They are the perfect upgrade for Porsche enthusiasts who demand the ease of access to vehicle's exhaust system. 



• Ultra-high-performance product
• Use of Titanium Ti6Al4V technology

Contains 12 x Studs, Nuts & Washers

Fits:
Porsche 911 1965-77
Porsche 964 (none Turbo)
Porsche 993 All
Porsche 996 (none Turbo)
Porsche 997 (none Turbo)
Porsche 986 All
Porsche 987 All
Porsche 718 4 Cyl Turbo

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

TITANSTUDS12

The product you are viewing cross references to these numbers

These titanium components are resistant to rust and corrosion, which can be a common issue with traditional steel studs and nuts. This corrosion resistance ensures that the studs and nuts maintain their integrity, allowing for easy removal and installation when necessary. They are the perfect upgrade for Porsche enthusiasts who demand the ease of access to vehicle's exhaust system. 



• Ultra-high-performance product
• Use of Titanium Ti6Al4V technology

Contains 18 x Studs, Nuts & Washers

Fits:
Porsche 996 Turbo / GT3 / GT2
Porsche 997 Turbo / GT3 / GT2
Porsche 997.2 ALL
Porsche 991 ALL
Porsche 992 ALL
Porsche 987 2009-12
Porsche 981
Porsche 718 GT4

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

TITANSTUDS18

The product you are viewing cross references to these numbers

Titanium exhaust manifold bolt M8x27. 
Set of 12  (OE Ref: 99907358901) 



Titanium is a highly corrosion-resistant material, which is particularly important in exhaust systems due to the exposure to extreme heat and moisture. The corrosion resistance of titanium bolts ensures longevity and reduces the risk of premature failure, ultimately saving the owner from costly repairs.

Fits:
Porsche 986 Boxster 1997-2004
Porsche 987 Boxster 2005-2008
Porsche 987C Cayman 2006-2008
Porsche 996 Carrera 1998-2004
Porsche 997.1 Carrera 2005-2008
Porsche 718 (982) Boxster 2017-2021
Porsche 718 (982C) Cayman 2017-2021

Click 'Zoom in' for large parts diagram.
Diagram ref no 3

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

TITANTORXLONG12

The product you are viewing cross references to these numbers

Performance headers Improve exhaust flow and sports car sound, designed for customer with tuned vehicles as these are catalytic bypass units.



Fits:
Porsche 982 Boxster / Cayman GTS 4.0L
Porsche 982 Boxster Spyder

Porsche 982C Cayman GT4


• Sport catalytic converters bypass for maximum performance
• Constructed from equal-length T304 stainless steel
• C.N.C. mandrel-bent tubing for improved torque and equalized engine pulsing
• More power and torque across the RPM band and dramatically improved sports car sound
• Direct replacement for the OEM headers with no cutting or welding required

Please note: Sports catalytic converters or bypass pipes do have type approval and may not be legally installed on vehicles manufactured after 1^st March 2001. They can not be used on a public road and are not MOT compliant, they are designed for race and track cars only.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3606107185

The product you are viewing cross references to these numbers

High performance stud + nut kits for the exhaust manifold to cylinder head for Porsche. Using titanium and Inconel alloy studs, aerospace lock nuts, and a well-thought and balanced combination of metals and plating/coatings, our fasteners will perform better than the traditional fastener. They will never oxidize, and hence will unscrew easily when required.



Novel ultra-high-performance product
• Use of Inconel 718 and aerospace technology
• Extreme perceived quality

Contains 12 x Studs, Nuts & Washers

Fits:
Porsche 911 1965-77
Porsche 964 (non Turbo)
Porsche 993 All
Porsche 996 (non Turbo)
Porsche 997 (non Turbo)
Porsche 986 All
Porsche 987 All
Porsche 718 4 Cyl Turbo

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SL-In-12

The product you are viewing cross references to these numbers

High performance stud + nut kits for the exhaust manifold to cylinder head for Porsche. Using titanium and Inconel alloy studs, aerospace lock nuts, and a well-thought and balanced combination of metals and plating/coatings, our fasteners will perform better than the traditional fastener. They will never oxidize, and hence will unscrew easily when required.



Novel ultra-high-performance product
• Use of Inconel 718 and aerospace technology
• Extreme perceived quality

Contains 18 x Studs, Nuts & Washers

Fits:
Porsche 996 Turbo / GT3 / GT2
Porsche 997 Turbo / GT3 / GT2
Porsche 997.2 ALL
Porsche 991 ALL
Porsche 992 ALL
Porsche 987 2009-12
Porsche 981
Porsche 718 GT4

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SL-In-18

The product you are viewing cross references to these numbers

RENNKRAFT™ Modular street and racing headers with HJS catalytic converters.



These modular headers are the perfect solution for any street driven 4.0 liter Cayman or Boxster. Our modular design features a quick release V-band connector that allows the owner to easily swap between our German made HJS 200 cell cats and a cat bypass "straight pipes" for track use. Rennkraft, translated from German is "race power". These unique headers offer true street and racetrack functionality in an innovative precision engineered package.

SOUND:

Many have complained about the lack of sound with the new 718 4.0ltr cars, these high flowing headers completely solve that issue. Equipped with our 200 cell cats, you will get a louder exhaust note with a much more raw sound. Higher frequency tones are more defined, and deceleration burbles are more robust and transparent. With the cat bypass pipes installed, you're in store for a sound much more akin to a 911 CUP car than a Porsche street car. The volume isn't overbearing, but the sound is very aggressive and race bred. It totally changes the character of the car. With the stock muffler in place, there is no drone what-so-ever, even with our Over Axle GPF Delete Pipes also installed.

POWER:

After extensive dyno development we found that mid length headers made the most power across the entire power band. With no tune, compared to a stock car we gained 31 whp and 19 ft/lbs of TQ at 7400 RPM with Sport Cats and 33 whp and 24 ft/lbs of TQ at 7200 RPM with Cat Bypass Pipes installed. That's a gain of 33 HP and 36 HP, respectively, at the crank! Peak horsepower also increased from our baseline of 383 whp to 405 whp with our HJS Sport Cats and 409 whp with Cat Bypass Pipes. See our dyno graph above for more details.

FEATURES:

• Fits all Porsche 4.0L Cayman/Boxster GT4/GTS/Spyder vehicles 2020+
• Impressive dyno proven power gains of 31 whp and 19 ft/lbs of TQ with the Sport Cats and 33 whp and 24 ft/lbs of TQ with Cat Bypass installed
• Save 2 lbs / 0.9 KGs with Sport Cats and 7 lbs / 3.2 KGs with Cat Bypass compared to the factory headers
• Modular design that uses a V-band clamp so one can quickly swap between cats and cat bypass
• Switching to cat-bypass for track events prevents catalytic converter degradation during all out competition racing abuse
• F1 style high velocity merge collectors
• Designed from 3D scans of the OEM headers so we can achieve perfect bolt-on fitment
• We use German-made HJS HD tri-metallic 200-cell EURO 6 homologated catalytic converters for the best performance and reliability
• We use the largest catalytic converters that will fit in the factory location for maximum flow
• Flows 93% of a 2.5 in straight pipe
• Will NOT cause a CEL (Check engine light), NO P420 or P430 codes, when Sport Cats are installed
• No ECU tune required
• NOT EPA or CARB Certified and not be used on street driven vehicles
• Will fit with any brand of aftermarket exhaust system designed to work with the factory headers
• Built 100% in house at Fabspeed Motorsport USA in Fort Washington, PA
• These are the very finest headers for the 718 4.0 liter cars and where developed in collaboration with HJS Emissions Technology
• 25+ years of air-cooled and water-cooled Porsche experience went into our design for these hand-crafted headers
• Constructed from CNC mandrel-bent T304L stainless steel
• Simple DIY (Do-It-Yourself) bolt-on installation, no cutting or welding required
• All Fabspeed performance products are backed by the Fabspeed Lifetime Warranty.

Why We Choose HJS Catalytic Converters:

HJS German imported catalytic converters are made from some of the highest grade materials you can find in a catalytic converter. This yields high performance gains and longevity so it wont deteriorate over time like lower grade catalytic converters. These catalytic converters flow up to 93-95% of a straight pipe in most applications. The benefit is that you get the "straight pipe sound" while still being able to provide enough emissions scrubbing to prevent a check engine light.

Sport Catalytic Converter (STREET) - This product removes the OEM catalytic converters from the vehicle, and as such, is strictly intended for closed track events and off-road use only. This product contains a High-Flow Sport Catalytic Converter solely intended for track and race cars as it is NOT California Air Resources Board Certified and not EPA certified. You are hereby informed and warned to check your local, state, and federals laws before buying and installing these or any aftermarket parts to be sure whether usage is in violation. All installation-risk and use-risk is borne by the end-user and installer of these parts.

Cat Bypass (RACE) - This product removes the OEM catalytic converters from the vehicle, and as such, is strictly intended for closed track events and off-road use only. This product is or contains a Racing Cat Bypass Pipe, which will give you check engine lights on OBD2 cars. We suggest pairing this product with racing software to prevent fault codes and check engine lights. Racing Cat Bypass Pipes are solely intended for track and race cars as they are NOT California Air Resources Board Certified and not EPA certified. You are hereby informed and warned to check your local, state, and federals laws before buying and installing these or any aftermarket parts to be sure whether usage is in violation. All installation-risk and use-risk is borne by the end-user and installer of these parts.

Please note: This is a special-order item manufactured to order. In some cases, please allow 4 – 5 weeks for the delivery. Special order items cannot be cancelled from this supplier once your order has been placed.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

FSPOR718GT4MDLRHDR

The product you are viewing cross references to these numbers

High performance stud + nut kits for the exhaust manifold to cylinder head for Porsche. Using titanium and Inconel alloy studs, aerospace lock nuts, and a well-thought and balanced combination of metals and plating/coatings, our fasteners will perform better than the traditional fastener. They will never oxidize, and hence will unscrew easily when required.



Novel ultra-high-performance product
• Use of Titanium Ti6Al4V technology
• Extreme perceived quality

Contains 12 x Studs, Nuts & Washers

Fits:
Porsche 911 1965-77
Porsche 964 (none Turbo)
Porsche 993 All
Porsche 996 (none Turbo)
Porsche 997 (none Turbo)
Porsche 986 All
Porsche 987 All
Porsche 718 4 Cyl Turbo

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SL-Ti-121

The product you are viewing cross references to these numbers

High performance stud + nut kits for the exhaust manifold to cylinder head for Porsche. Using titanium and Inconel alloy studs, aerospace lock nuts, and a well-thought and balanced combination of metals and plating/coatings, our fasteners will perform better than the traditional fastener. They will never oxidize, and hence will unscrew easily when required.



Novel ultra-high-performance product
• Use of Titanium Ti6Al4V technology
• Extreme perceived quality

Contains 18 x Studs, Nuts & Washers

Fits:
Porsche 996 Turbo / GT3 / GT2
Porsche 997 Turbo / GT3 / GT2
Porsche 997.2 ALL
Porsche 991 ALL
Porsche 992 ALL
Porsche 987 2009-12
Porsche 981
Porsche 718 GT4

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SL-Ti-18

The product you are viewing cross references to these numbers