Bump steer correcting tie rod kit. Porsche 964 W/O RS Wheel Carriers - 2180031
代码: 2180031
Bump steer correcting tie rod kit.
Bump geometry correction. 1 kit, req'd per car.
For Porsche 964 1989-94 W/O RS Wheel Carriers
Lowered cars with non-RS wheel carriers suffer from bump steer and will benefit from bump geometry correction.
Bump steer is a change in toe due to vertical movement of the wheel, such as when driving over a bump. The toe change causes the car to turn, and the driver needs to constantly correct for this to maintain a steady trajectory. This makes the car a handful to drive, especially over bumpy road surfaces.
Bump correction is achieved by moving the tie rod end pivot about 10mm closer to the steering knuckle as compared to the stock tie rod end. This changes the angle of the tie rod to produce the bump geometry correction.
No Need To Convert Wheel Carriers
This Bump Steer Correcting Tie Rod kit provides bump geometry correction with the standard C2/C4 wheel carriers. It is not necessary to convert the wheel carriers to RS type to correct for bump steer when using our kit.
These Elephant Racing bump steer tie rods also eliminate the compliant rubber inner-joint found in the factory 964 tie rods with a spherical bearing providing a more direct and responsive steering feel. Thus, proper suspension geometry is restored, driver corrections are minimized, and vehicle trajectory is stabilized making driving control easier while reducing driver fatigue.
Out Performs All Other Tie Rods
Even on cars fresh from the Porsche factory assembly lines our anti-bump steer kit will reduce bump steer through the full range of motion.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180031
您正在查看的产品与这些编号存在交叉引用关系
Bump geometry correction. 1 kit, req'd per car.
For Porsche 964 1989-94 W/O RS Wheel Carriers
Lowered cars with non-RS wheel carriers suffer from bump steer and will benefit from bump geometry correction.
Bump steer is a change in toe due to vertical movement of the wheel, such as when driving over a bump. The toe change causes the car to turn, and the driver needs to constantly correct for this to maintain a steady trajectory. This makes the car a handful to drive, especially over bumpy road surfaces.
Bump correction is achieved by moving the tie rod end pivot about 10mm closer to the steering knuckle as compared to the stock tie rod end. This changes the angle of the tie rod to produce the bump geometry correction.
No Need To Convert Wheel Carriers
This Bump Steer Correcting Tie Rod kit provides bump geometry correction with the standard C2/C4 wheel carriers. It is not necessary to convert the wheel carriers to RS type to correct for bump steer when using our kit.
- Corrects for bump steer
- Eliminates rubber inner-joint
- Enhanced driving precision
- Easier and more cost effective than RS wheel carrier conversion
These Elephant Racing bump steer tie rods also eliminate the compliant rubber inner-joint found in the factory 964 tie rods with a spherical bearing providing a more direct and responsive steering feel. Thus, proper suspension geometry is restored, driver corrections are minimized, and vehicle trajectory is stabilized making driving control easier while reducing driver fatigue.
Out Performs All Other Tie Rods
Even on cars fresh from the Porsche factory assembly lines our anti-bump steer kit will reduce bump steer through the full range of motion.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
2180031
2180031
96434703200
96434703202
您正在查看的产品与这些编号存在交叉引用关系
产品车辆组
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
€768.18
当前 €752.82
即将抵达
也可在这些页面找到