电池和充电器

CTEK battery conditioner comfort indicator with a 1.5m cable



Fit this comfort indicator to your battery to show the battery condition and a allow quick and easy connection for the battery conditioner

Comes with a 1.5m cable

Fits into carpet or trim panels for a factory finish look

Just plug in the conditioner into the indicator instead of connecting clamps to the battery terminals

• A quick connector and indicator especially developed for panel mounting
• The indicator clearly and simply shows the battery charge level
• Cable length - 150 cm (330cm - 56-531). Eyelet terminal -M8 (8.4mm) on both models. Size connector/indicator - 35 mm x 21 mm 50 mm. Fuse -15A

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

56-380

您正在查看的产品与这些编号存在交叉引用关系

CTEK battery conditioner comfort indicator with a 3.3m cable



Fit this comfort indicator to your battery to show the battery condition and a allow quick and easy connection for the battery conditioner

Comes with a 3.3m cable

Fits into carpet or trim panels for a factory finish look

Just plug in the conditioner into the indicator instead of connecting clamps to the battery terminals

• A quick connector and indicator especially developed for panel mounting
• The indicator clearly and simply shows the battery charge level
• Cable length - 330 cm
Eyelet terminal -M8 (8.4mm) on both models. Size connector/indicator - 35 mm x 21 mm 50 mm. Fuse -15A

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

56-531

您正在查看的产品与这些编号存在交叉引用关系

CTEK battery conditioner comfort indicator with status lights



Fit this comfort indicator to your battery to show the battery condition and a allow quick and easy connection for the battery conditioner
The battery condition is shown through status lights on the unit

Just plug in the conditioner into the indicator instead of connecting clamps to the battery terminals

• Comfort Indicator uses a simple traffic light system to show the state of charge on your battery
• 8mm Eyelet Adaptors
• 15A blade type fuse
• Compatible with XS 0.8, MXS 3.8, MXS 7.0, MXS 10, M45 & M100
• Back current drain ~ 1Ah / Month
• 10A maximum current
• Easy to use and ideal for workshops and showrooms

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

56-382

您正在查看的产品与这些编号存在交叉引用关系

CTEK battery conditioner CTX indicator with M8 eyelet



Checks charge status of hard to reach batteries, M8 8.4mm eyelet

Indicator is the easiest way to monitor the charge in your battery. An accurate reading for your battery is displayed two hours after you've used your vehicle.

Fit this comfort CTX indicator to your battery to enable a quick and easy connection to your CTEK battery conditioner

Just plug in the conditioner instead of connecting clamps to the battery terminals

• Comfort Indicator uses a simple traffic light system to show the state of charge on your battery
• 8mm eyelet fitting
• Enables batteries to be charged in hard to reach places where using clamps is inconvenient
• 15A blade type fuse
• Compatible with XC 0.8, XS 0.8, MXS 3.8, MXS 5.0, MXS 7.0, MXS 10, M45 & M100
• Back current drain - 1Ah / Month
• 10A maximum current

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

40-133

您正在查看的产品与这些编号存在交叉引用关系

CTEK MXS 3.8 智能电池调节器/充电器
汽车、摩托车电池自动维护充电器



MXS 3.8 微处理器控制的 7 步电池充电器和维护器适用于 1.2Ah-85Ah 的电池。
其功能包括电池诊断以确定您的电池是否能够接收和保留电量、专利的脱硫化程序和用于寒冷天气充电的“雪花”程序。
它还包括用于为较小电池和普通电池充电的可选程序。
MXS 3.8 采用 CTEK 专利的浮动/脉冲系统，这是电池长时间连接时最有效的维护模式。MXS 3.8 使用简单，您可以在清晰易读的显示屏上跟踪整个充电过程。

• 可充电至 32Ah 的电池。可维护高达 100Ah 的大型电池
• 全自动 6 级充电，包括专利的去硫化和脉冲维护程序

• 可维护高达 130Ah 的电池
• 防溅防尘 (IP65)
• 安全无火花操作
• 防短路

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

56-972

您正在查看的产品与这些编号存在交叉引用关系

CTEK XS 0.8 Smart battery conditioner and charger
Compact trickle charger for smaller batteries



The XS 0.8 uses state of the art technology for charging smaller batteries on motorbikes, jet skis, ATVs and lawnmowers.
The XS 0.8 is CTEK's smallest 12V charger and it's suitable for charging smaller batteries as well as maintenance charging normal sized car batteries.
The XS 0.8 is a compact, fully automatic 6 step charger that delivers 0.8A and charges 12V batteries from 1.2 to 32Ah and maintenance charging up to 100Ah.
It's simple to use and you can follow the whole charging process on the clear, easy to read display.

• Charges batteries up to 32Ah. Maintains larger batteries up to 100Ah
• Fully automatic, 6-stage charging includes patented desuplhation and pulse maintenance programmes
• Compact tough design - splash resistant & dust-proof to IP65
• Comes with accessories for connection to different types of battery
• Splash and dust proof (IP65)
• Safe spark free operation
• Reverse polarity protected
•Short circuit proof
• 5-year warranty

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

56-833

您正在查看的产品与这些编号存在交叉引用关系

Gearbox Ground Strap.



Fits:
Porsche 911 - 1965 to 1973 Manual  and Sportomatic

Porsche 911 - 1974 to 1983 Sportomatic
Porsche 356 - 1950 to 1965

Click 'Zoom in' for large parts diagram.
Diagram ref no 62

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99961191820

您正在查看的产品与这些编号存在交叉引用关系

Gearbox Ground Strap.



Fits:
Porsche 911 - 1970 to 1989

Porsche 911 turbo - 1975 to 1989
Porsche 964 - 1989 to 1994 Manual Transmission
Porsche 993 - 1994 to 1998 Manual Transmission

Click 'Zoom in' for large parts diagram.
Diagram ref no 40

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99961192020

您正在查看的产品与这些编号存在交叉引用关系

Gearbox Ground Strap.



Fits:
Porsche 911 - 1970 to 1989

Porsche 911 turbo - 1975 to 1989
Porsche 964 - 1989 to 1994 Manual Transmission
Porsche 993 - 1994 to 1998 Manual Transmission

Click 'Zoom in' for large parts diagram.
Diagram ref no 40

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99961192020

您正在查看的产品与这些编号存在交叉引用关系

Lightweight lithium 20Ah (60Ah PbEq) Touge 500 battery.
Only 3.8 kg

PbEq: (LeadEquivalent) is to help you choose the correct Capacity for your vehicle.
As a rule of thumb, we recommend that the capacity in Ah (PbEq) of our battery should be at least the same or greater than your OEM battery

This battery has a 650 CCA (Cold Cranking Amps) rating

Fits
Porsche 911 - 1965 to 1989
Porsche 964 - 1989 to 1994
Porsche 993 - 1994 to 1998
Porsche 944 - 1982 to 1991
Porsche 968 - 1992 to 1995

Save over 17kgs with the Touge 500 battery using the Latest Lithium Iron Phosphate (LiFePO4) Battery Technology.

The focus here is to better the performance of a lead-acid battery at a fraction of the weight.

• Only 3.8 kg (Typical OEM lead acid batteries weigh between 15kgs to 27kgs)
• Capacity - 60Ah (PbEq)
• Crank - 650 CCA
• Nominal Voltage - 12.8 Volts
• Dimensions - 240 x 175 x 190mm

Product Information
• 2 year limited warranty
• Suitable for up to 5.0L and 8 cylinder engines
• Developed in the UK
• Built using high tech a123 battery cells from the US
• Tested on road and track
• OEM style fitment on many cars
• UK Motorsport Association (MSA) approved for racing

Please note: due to logistic restrictions, we are only able to deliver batteries within United Kingdom and Netherlands

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

650CCA

您正在查看的产品与这些编号存在交叉引用关系

Positive battery terminal clamp.



Fits:
Porsche 911 (1974-1989)
Porsche 930 (1976-1989)

Click 'Zoom in' for large parts diagram.
Diagram ref no 6

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91161189804

您正在查看的产品与这些编号存在交叉引用关系

Fits:
Porsche 911 / 930 / 912 / 996 / 997 / Boxster / Cayman / 991
** except 1969-73

This unit is designed to work with the Odyssey 925 lightweight battery. Other batteries of similar size may also fit, see our battery section for more details.
Note: Switch, remote pull, and battery are not included with this or any of the kits.

Rennline Battery Relocation Kit with Kill Switch Mount (Without Kill Switch - available separately)

To be fitted with 925 Odyssey Battery

Fits:
Porsche 911 LHD Only

Relocating a lightweight battery to the smugglers box is a standard modification to track and high-performance street 911's. The stock 911 battery is much heavier than necessary (upward of 40 pounds heavier than an Odyssey 680), and is located in the front left of the car, where it contributes to poor weight distribution. Until now, relocating a battery to the smugglers box (the smugglers box is the small compartment in the front trunk behind the fuel tank, on the passenger's side) required fabricating your own mounting and bracket system. Rennline's new relocation kit is a fully adjustable aluminum assembly that makes battery relocation an easy afternoon project. This newly designed unit is a complete bolt in assembly which requires absolutely no drilling and fully suspends the battery eliminating unwanted vibration. Kit includes all necessary stainless steel hardware and full installation instructions.We also offer an optional Smugglers Box Lid that is a perfect location to mount a cut off switch.


Note: Switch, remote pull, smugglers box cover, and battery are not included with this or any of the kits.

Note: Pictures may not show actual product.

Rennline Battery Relocation Kit with Kill Switch Mount (Without Kill Switch - available separately)

To be fitted with 680 Odyssey Battery

Fits:
Porsche 911 LHD Only

Relocating a lightweight battery to the smugglers box is a standard modification to track and high-performance street 911's. The stock 911 battery is much heavier than necessary (upward of 40 pounds heavier than an Odyssey 680), and is located in the front left of the car, where it contributes to poor weight distribution. Until now, relocating a battery to the smugglers box (the smugglers box is the small compartment in the front trunk behind the fuel tank, on the passenger's side) required fabricating your own mounting and bracket system. Rennline's new relocation kit is a fully adjustable aluminum assembly that makes battery relocation an easy afternoon project. This newly designed unit is a complete bolt in assembly which requires absolutely no drilling and fully suspends the battery eliminating unwanted vibration. Kit includes all necessary stainless steel hardware and full installation instructions.We also offer an optional Smugglers Box Lid that is a perfect location to mount a cut off switch.


Note: Switch, remote pull, smugglers box cover, and battery are not included with this or any of the kits.

Note: Pictures may not show actual product.

Rennline Battery Relocation Kit without Kill Switch Mount

To be fitted with 925 Odyssey Battery

Fits:
Porsche 911 LHD Only


Relocating a lightweight battery to the smugglers box is a standard modification to track and high-performance street 911's. The stock 911 battery is much heavier than necessary (upward of 40 pounds heavier than an Odyssey 680), and is located in the front left of the car, where it contributes to poor weight distribution. Until now, relocating a battery to the smugglers box (the smugglers box is the small compartment in the front trunk behind the fuel tank, on the passenger's side) required fabricating your own mounting and bracket system. Rennline's new relocation kit is a fully adjustable aluminum assembly that makes battery relocation an easy afternoon project. This newly designed unit is a complete bolt in assembly which requires absolutely no drilling and fully suspends the battery eliminating unwanted vibration. Kit includes all necessary stainless steel hardware and full installation instructions.We also offer an optional Smugglers Box Lid that is a perfect location to mount a cut off switch.


Note: Switch, remote pull, smugglers box cover, and battery are not included with this or any of the kits.

Note: Pictures may not show actual product.

Rennline Battery Relocation Kit without Kill Switch Mount

To be fitted with 680 Odyssey Battery

Fits:
Porsche 911 LHD Only

Relocating a lightweight battery to the smugglers box is a standard modification to track and high-performance street 911's. The stock 911 battery is much heavier than necessary (upward of 40 pounds heavier than an Odyssey 680), and is located in the front left of the car, where it contributes to poor weight distribution. Until now, relocating a battery to the smugglers box (the smugglers box is the small compartment in the front trunk behind the fuel tank, on the passenger's side) required fabricating your own mounting and bracket system. Rennline's new relocation kit is a fully adjustable aluminum assembly that makes battery relocation an easy afternoon project. This newly designed unit is a complete bolt in assembly which requires absolutely no drilling and fully suspends the battery eliminating unwanted vibration. Kit includes all necessary stainless steel hardware and full installation instructions.We also offer an optional Smugglers Box Lid that is a perfect location to mount a cut off switch.


Note: Switch, remote pull, smugglers box cover, and battery are not included with this or any of the kits.

Note: Pictures may not show actual product.

Rennline Kill Switch Mount.
You may also need the pull cable EL21 Works with all Rennline kill switches EL61

Fits:
Porsche 911
Porsche 964
Porsche 993

This kill switch mount is specifically designed to attach to the inner fender bolts on all 1965-98 911’s. We have also added extra mounting holes that will allow this bracket to be used in many universal applications. It accepts most standard kill switches and up to 2 remotes pulls that are required in any organized race environment. Constructed from anodized aluminum and TIG welded to create a bullet proof design. Kill switch and remote pulls are sold separately.

Note: Pictures may not show actual product.

Wing nut for ground strap to body.



Fits:
Porsche 911 (1969-1977)
Porsche 930 (1976-1977)

Click 'Zoom in' for large parts diagram.
Diagram ref no 5

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99904400103

您正在查看的产品与这些编号存在交叉引用关系

Wing nut for ground strap to body.



Fits:
Porsche 911 (1974-1977)
Porsche 930 (1976-1977)

Click 'Zoom in' for large parts diagram.
Diagram ref no 5

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99904400103

您正在查看的产品与这些编号存在交叉引用关系