化油器及零件

Gasket set for Weber 40 carburettor
Set of 2 kits



For installation in:
Porsche 911 F (1965 - 1971) ONLY with Weber 40 carburettor
Porsche 914/6 (1970 - 1972)

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PCG10894800

您正在查看的产品与这些编号存在交叉引用关系

Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.

Installation Packages are suitable for Porsche 911 SC - 3.0L engines (Model Years 1974-1985).

Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensors (TPS) Mounting Kits.
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Available in 18 anodised colour options.
• Available with 39mm Inlet Ports.
Installation Kit:
• ECU including base map package - Comes complete with full electrical engine harness, Coil pack, HT leads, engine sensors, hardware and software.
• Trigger Wheel & Fan Pulley assembly, including sensor mounting bracket and Distributor blanking plug.
• Fuelling System - Includes Fuel Injectors, Fuel pressure regulator with gauge, Fuel Lines, fittings and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assit.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Megaflow Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.
• Heater duct system.

**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00087-01
Parts are in silver. The contents of these kits may vary, from the images provided

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

102-102-00238-01KIT

您正在查看的产品与这些编号存在交叉引用关系

Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.


Installation Packages are suitable for Porsche 911 - 3.2L engines (Model Years 1986-1989).

Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.

Supporting parts that create these Full Plug, Play and Tune - Installation Kits:
• ECU GP Lite patch harness including base map package - Comes complete with electrical patch harnesses, hardware, and software.
• Fuelling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system.

**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00086-01
Parts are in silver. The contents of these kits may vary, from the images provided

Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.


Installation Packages are suitable for Porsche 911 - 3.2L engines (Model Years 1986-1989).
Kits are made in Silver

Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.

Supporting parts that create these Full Plug, Play and Tune - Installation Kits:
• ECU GPA full harness including base map package - Comes complete with electrical full harnesses, hardware, and software.
• Fueling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system.

**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00086-01
Parts are in silver. The contents of these kits may vary, from the images provided

Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.

Installation Packages are suitable for Porsche 911 - 3.2L engines (Model Years 1986-1989).

Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.

Supporting parts that create these Full Plug, Play and Tune - Installation Kits:
• ECU including base map package - Comes complete with electrical patch harnesses, hardware, and software.
• Fuelling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system.

**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00086-01
Parts are in silver. The contents of these kits may vary, from the images provided

Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.

Porsche 911E, T and S 1969 to 1973 (2.2 and 2.4 Ltr) engines.

Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensors (TPS) Mounting Kits.
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Available in 18 anodised colour options.
• Available with 39mm Inlet Ports.
Installation Kit:
• Emerald3D-K6 ECU including base map package, complete with full electrical engine harness/ Trigger Wheel & Fan Pulley Assembly, hardware, and software.
• Fuelling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off kit for brake boost an/or Idle Air Control (IAC) assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system - for interior (Cabin) heating.
• Rain Guard Kit for protection against rain water ingress.

**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00088-01
Parts are in silver. The contents of these kits may vary, from the images provided

Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.

Installation Packages are suitable for Porsche 911 SC - 3.0L engines (Model Years 1974-1985).

Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensors (TPS) Mounting Kits.
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Available in 18 anodised colour options.
• Available with 39mm Inlet Ports.
Installation Kit:
• GPA ECU including base map package - Comes complete with full electrical engine harness, Coil pack, HT leads, engine sensors, hardware and software.
• Trigger Wheel & Fan Pulley assembly, including sensor mounting bracket and Distributor blanking plug.
• Fuelling System - Includes Fuel Injectors, Fuel pressure regulator with gauge, Fuel Lines, fittings and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off & idle air control assembly, c/w interfacing pipework for cold start engine idle control & brake boost assit.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Megaflow Air Filtration System - Includes Megaflow Air Filters complete with brushed aluminium pre-drilled Filter back plates.
• Heater duct system.

**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00087-01
Parts are in silver. The contents of these kits may vary, from the images provided

Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.
This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.

Porsche 911E, T and S 1969 to 1973 (2.2 and 2.4 Ltr) engines.

Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:
• Aerospace Grade Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Aluminium Inlets/Extensions are suitable for duck or whale tail models.
• Aluminium Ram Pipes.
• Throttle Position Sensors (TPS) Mounting Kits.
• Billet Aluminium Fuel Rails.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.
• Available in 18 anodised colour options.
• Available with 39mm Inlet Ports.
Installation Kit:
• GPA ECU including base map package, complete with full electrical engine harness/ Trigger Wheel & Fan Pulley Assembly, hardware, and software.
• Fueling System - Includes Fuel pressure regulator with gauge, Fuel Lines, fittings, and hoses to interface with existing fuel system
• Vacuum System - Includes vacuum take-off kit for brake boost an/or Idle Air Control (IAC) assembly, c/w interfacing pipework for cold start engine idle control & brake boost assist.
• Engine Oil breather system - Includes all filters and interfacing components required.
• Heater duct system - for interior (Cabin) heating.
• Rain Guard Kit for protection against rain water ingress.

**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00088-01
Parts are in silver. The contents of these kits may vary, from the images provided