发动机螺栓/螺柱

High performance stud + nut kits for the exhaust manifold to cylinder head for Porsche. Using titanium and Inconel alloy studs, aerospace lock nuts, and a well-thought and balanced combination of metals and plating/coatings, our fasteners will perform better than the traditional fastener. They will never oxidize, and hence will unscrew easily when required.



Novel ultra-high-performance product
• Use of Inconel 718 and aerospace technology
• Extreme perceived quality

Contains 12 x Studs, Nuts & Washers

Fits:
Porsche 911 1965-77
Porsche 964 (non Turbo)
Porsche 993 All
Porsche 996 (non Turbo)
Porsche 997 (non Turbo)
Porsche 986 All
Porsche 987 All
Porsche 718 4 Cyl Turbo

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SL-In-12

您正在查看的产品与这些编号存在交叉引用关系

Screw for crankcase.



Fits:
Porsche 911 /S (1965 to 1977; with 2.7L engines)
Porsche 914-6 (1970 to 1972)

Click 'Zoom in' for large parts diagram.
Diagram ref no 29

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

90110117300

您正在查看的产品与这些编号存在交叉引用关系

Stud bolt, M10x69. Each.



Fits:
Porsche 914/6 (1970 - 1972)
Porsche 911 F  (1965 - 1973)
Porsche 911 Carrera (1984 - 1986)
Porsche 911 Turbo (1975 - 1986)

Click 'Zoom in' for large parts diagram.
Diagram ref no 6 (and no 7 for 914 only)

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99906103402

您正在查看的产品与这些编号存在交叉引用关系

Through bolt o-ring installer for Porsche 911



Installing O-rings on the through bolts for a 911 engine case often slices the rings on the threads of the bolt, leading to ripped seals at best, or a leaky engine at worst. Use this cap to protect the O-ring and to insure a factory quality seal. Precisely machined from quality brass.

Stomski Racing SR024 Through bolt o-ring installer with sleeve for Porsche 911



Based on the factory P9511 tool, STOMSKI RACING's version of this tool incorporates a brass cap and a double-ended stainless steel sleeve to install the o-rings on the crankcase through-bolts of the 3.6 and later cases (but possibly can be used on some other 911 engines). By using the included brass cap to protect the delicate o-ring from getting cut on the threads of the bolt, you then use the "thin" end of the sleeve to slide the o-ring over the brass cap onto the shank of the through-bolt. Once the o-ring is clear of the threads, remove the SR024 brass cap and flip the SR024 stainless steel sleeve over and use the blunted end to securely and gently seat the o-ring in the recess on the 3.6 case.

High performance stud + nut kits for the exhaust manifold to cylinder head for Porsche. Using titanium and Inconel alloy studs, aerospace lock nuts, and a well-thought and balanced combination of metals and plating/coatings, our fasteners will perform better than the traditional fastener. They will never oxidize, and hence will unscrew easily when required.



Novel ultra-high-performance product
• Use of Titanium Ti6Al4V technology
• Extreme perceived quality

Contains 12 x Studs, Nuts & Washers

Fits:
Porsche 911 1965-77
Porsche 964 (none Turbo)
Porsche 993 All
Porsche 996 (none Turbo)
Porsche 997 (none Turbo)
Porsche 986 All
Porsche 987 All
Porsche 718 4 Cyl Turbo

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SL-Ti-121

您正在查看的产品与这些编号存在交叉引用关系