发动机螺栓/螺柱

Exhaust head stud, L - 45mm.
Sold each.



Fits:
Porsche 911 3.2L 1984-89
Porsche 930 turbo
Porsche 965 turbo

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99906223902

您正在查看的产品与这些编号存在交叉引用关系

Gearbox housing stud, M 10 X 25.



Fits:
Porsche 911 1972-73 (TYP 915)
Porsche 911 1974-89
Porsche 911 (930) Turbo 1975-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 7

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99906218202

您正在查看的产品与这些编号存在交叉引用关系

Gearbox housing stud, M 8 X 38.



Fits:
Porsche 911 / SC / Carrera 1977-86
Porsche 911 Turbo 1977-77
Porsche 924  1976-79 with 5-Speed Gearbox
Porsche 924 Turbo/ GT 1980-85 Manual Gearbox G31.01/02/03

Click 'Zoom in' for large parts diagram.
Diagram ref no. 2 (for 911) or no.19 (for 924)

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99906209802

您正在查看的产品与这些编号存在交叉引用关系

Head nut washer. 24 per engine. Price is for each.



Fits:
Porsche 911 1978-89

Click 'Zoom in' for large parts diagram.
Diagram Ref No 16.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99903109101

您正在查看的产品与这些编号存在交叉引用关系

Head nut washer. 24 per engine. Price is for each.



Fits:
Porsche 911 1978-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 16.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99903109101

您正在查看的产品与这些编号存在交叉引用关系

Stud bolt, M10x69. Each.



Fits:
Porsche 914/6 (1970 - 1972)
Porsche 911 F  (1965 - 1973)
Porsche 911 Carrera (1984 - 1986)
Porsche 911 Turbo (1975 - 1986)

Click 'Zoom in' for large parts diagram.
Diagram ref no 6 (and no 7 for 914 only)

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99906103402

您正在查看的产品与这些编号存在交叉引用关系

Through bolt o-ring installer for Porsche 911



Installing O-rings on the through bolts for a 911 engine case often slices the rings on the threads of the bolt, leading to ripped seals at best, or a leaky engine at worst. Use this cap to protect the O-ring and to insure a factory quality seal. Precisely machined from quality brass.

Stomski Racing SR024 Through bolt o-ring installer with sleeve for Porsche 911



Based on the factory P9511 tool, STOMSKI RACING's version of this tool incorporates a brass cap and a double-ended stainless steel sleeve to install the o-rings on the crankcase through-bolts of the 3.6 and later cases (but possibly can be used on some other 911 engines). By using the included brass cap to protect the delicate o-ring from getting cut on the threads of the bolt, you then use the "thin" end of the sleeve to slide the o-ring over the brass cap onto the shank of the through-bolt. Once the o-ring is clear of the threads, remove the SR024 brass cap and flip the SR024 stainless steel sleeve over and use the blunted end to securely and gently seat the o-ring in the recess on the 3.6 case.

High performance stud + nut kits for the exhaust manifold to cylinder head for Porsche. Using titanium and Inconel alloy studs, aerospace lock nuts, and a well-thought and balanced combination of metals and plating/coatings, our fasteners will perform better than the traditional fastener. They will never oxidize, and hence will unscrew easily when required.



Novel ultra-high-performance product
• Use of Titanium Ti6Al4V technology
• Extreme perceived quality

Contains 12 x Studs, Nuts & Washers

Fits:
Porsche 911 3.0L SC
Porsche 911 3.2L 1984-89
Porsche 930 turbo
Porsche 965 turbo

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SL-Ti-122

您正在查看的产品与这些编号存在交叉引用关系

inlet manifold head stud in titanium.
M8 studs and nuts for 911 x set of 12
M6 studs and nuts for 964/993 x set of 18

Fits:
Porsche 911
Porsche 964 / 993

Our set is the perfect solution to future proof your intake manifold to cylinder head. 

The titanium alloy studs and nylon-lock nuts will not rust after repeated heat cycles and will be easily removed when needed. 
Ti6Al4V alloy is as strong as steel but 45% lighter. 

The fasteners are PVD Titanium nitride coated for extra protection and to emulate the classic appearance of the the yellow zinc steel plated hardware.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SL-Ti-In

您正在查看的产品与这些编号存在交叉引用关系