扭力杆

Chrome Moly Light Weight Hollow Front Torsion Bar (SET OF 2)
- 21mm
- 22mm

Tighten up your suspension with these high precision, light weight, hollow torsion bars.

Fabricated from aircraft quality 4130 chrome moly steel, and heat treated for high strength and reliability.

Zinc plated with plugged ends for superior corrosion resistance.

Precision machined splined ends for a perfect fit.

Center less ground and gun drilled for a consistent spring rate.

Lighter weight compared to solid bars with an equivalent stiffness. Up to 3 lbs lighter per bar!

These are the highest quality bars on the market.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

1S166911F

您正在查看的产品与这些编号存在交叉引用关系

QuickChange™ Torsion Bars, FRONT
Sold per kit, 1 kit req'd per car.



Fits:
Porsche 911/912/930 1965-89
Porsche 914 1970-76

QuickChange Torsion Bars are Plated & Plugged and include a female threaded end that you can engage with a bolt to use as a handle for easier extraction / insertion.

Use the rears bars in combination with our QuickChange™ Spring Plate products for fast torsion bar swapping and re-indexing. QuickChange™ Torsion Bars can be extracted through the QuickChange™ Spring Plate without removing any bolts. Alignment settings are maintained. You don't even need to remove the wheel from the car. Changing torsion bars is a 5 minute per side operation!

A QuickChange™ Insert is available separately for converting your existing hollow torsion bars.

QuickChange™ Torsion Bars make it easy to dislodge a stuck bar, and thereby offer benefits even when used on the front and with factory spring plates (factory spring do not allow the bars to be extracted without removing the plates).

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

209202

您正在查看的产品与这些编号存在交叉引用关系

QuickChange™ Torsion Bars, REAR
Sold per kit, 1 kit req'd per car.



Fits:
for G50 Transmission
Porsche 911 / 930 1987-89

QuickChange Torsion Bars are Plated & Plugged and include a female threaded end that you can engage with a bolt to use as a handle for easier extraction / insertion.

Use the rears bars in combination with our QuickChange™ Spring Plate products for fast torsion bar swapping and re-indexing. QuickChange™ Torsion Bars can be extracted through the QuickChange™ Spring Plate without removing any bolts. Alignment settings are maintained. You don't even need to remove the wheel from the car. Changing torsion bars is a 5 minute per side operation!

A QuickChange™ Insert is available separately for converting your existing hollow torsion bars.

QuickChange™ Torsion Bars make it easy to dislodge a stuck bar, and thereby offer benefits even when used on the front and with factory spring plates (factory spring do not allow the bars to be extracted without removing the plates).

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

21021

您正在查看的产品与这些编号存在交叉引用关系

QuickChange™ Torsion Bars, REAR
Sold per kit, 1 kit req'd per car.



Fits:
Porsche 911/912/930/914 '65-'86
Porsche 356 A/B '48-'65 (Pre-A, C and CS Read Notes),
Porsche 944/968/924 '76-'95 w/ QuickChange Spring Plates

PLEASE NOTE: sizes 34mm and 36mm are not applicable for 944, 968 and 924 models)

QuickChange Torsion Bars are Plated & Plugged and include a female threaded end that you can engage with a bolt to use as a handle for easier extraction / insertion.

Use the rears bars in combination with our QuickChange™ Spring Plate products for fast torsion bar swapping and re-indexing. QuickChange™ Torsion Bars can be extracted through the QuickChange™ Spring Plate without removing any bolts. Alignment settings are maintained. You don't even need to remove the wheel from the car. Changing torsion bars is a 5 minute per side operation!

A QuickChange™ Insert is available separately for converting your existing hollow torsion bars.

QuickChange™ Torsion Bars make it easy to dislodge a stuck bar, and thereby offer benefits even when used on the front and with factory spring plates (factory spring do not allow the bars to be extracted without removing the plates).

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

21020

您正在查看的产品与这些编号存在交叉引用关系