赛车运动零件

Our spray bar, made from stainless steel, is an excellent reproduction of the factory RSR spray bar. It allows for gear lube (presumably from a remote pump and cooler) to be returned directly to the gear mesh, including the final drive gears.

** This requires machining to the front "nose cone" housing.

We have updated our 915 spray bar kit to include an improved oil return port that will not interfere with the torsion bar tube and allows for better routing of the oil return line.

Fits all Porsche 930 4 speed transmissions

Precision machined
Improved design incorporates an oil groove promoting more lubrication to the input shaft bearings (some modification required to bell housing and shims)
Substantial clearances for ease of assembly
Perfect fit for bearings and assembly
Much stronger than the original cast part

Replaces part 930.302.121.00

Note: Do not use the factory lock washers in conjunction with our supplied hardware.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

93030212100

您正在查看的产品与这些编号存在交叉引用关系

Finally, conversion axle flanges for early 911s and 914s. These are machined in house from 4340 billet steel and heat treated.

Our custom "coarse spline/18 spline" drive flanges will allow 930 or G50 CV joints (with metal grease caps) to bolt up to the early 1969-75 911s and all 914 transaxles.

Shaft length was designed with the stock open diff in mind. If by off-chance you have a factory LSD, spacers will be required.

Sold in pairs.

Fits
Porsche 911 - 1969 to 1975
Porsche 914

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

CMS.914.18T

您正在查看的产品与这些编号存在交叉引用关系

Machined in house from 4340 steel and heat treated.

For all 930 4 speed applications and 1978 and later 915.

Spacers are required if you are using with a factory LSD.

Replaces part 930-332-209-12

Sold in pairs.

Notes:
Factory LSD applications will require spacers, otherwise the flanges will be too short.

Designed for use with metal CV gaskets, not paper.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

93033223200

您正在查看的产品与这些编号存在交叉引用关系

The original Porsche 930 transmission differential side cover is made of cast aluminum, not to mention it's pretty thin.
Under load there can be a tremendous force applied to this cover, and it can break, sometimes resulting in a damaged ring and pinion-or worse.
Upgrading to a billet side plate will add significant strength and increased reliability to the differential section.

Our design features include:

A ring gear thrust bolt to reduce ring gear deflection under load
Ports that can be used for an oil cooling system
Cross drilled oil passageways for the differential bearing

Comes with (3) 3/4 - 16 O ring plugs.

Replaces part 930.301.311.02

930/30, 930/33, 930/34, 930/36, 930/37, 930/67

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

93030131102

您正在查看的产品与这些编号存在交叉引用关系

We can provide bolt on hydraulic slave cylinder for your Porsche 911 930 4 speed transaxle eliminating all the woes that come with a clutch cable. It can be used for both upright and inverted applications - especially nice for mid engine conversions.

Includes clutch arm, cable clevis, slave cylinder and our billet slave cylinder bracket with bolts. Please specify if your application is using a short bell housing or long bell housing transaxle as the pivot shafts for the release fork are different. We must modify the arm if you have a long bell housing transmission.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

95011623714

您正在查看的产品与这些编号存在交叉引用关系

Our billet fork cover plate replaces part 915.303.023.02 and will allow you to scavenge oil without having to drill, tap or weld to the case. Within the oil passageway is a temp sender provision that is usable even when not utilizing the scavenge port.

Features:

Proper knock off tabs/pry points for easy removal
300F VDO temp sender included
-8AN oil scavenge port (-8AN adapter included)
Uses your existing fork, studs and dowel pins
Uses stock paper gasket

Fits all Porsche 915 and 930 transmissions.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91530302302

您正在查看的产品与这些编号存在交叉引用关系

A direct replacement for part 915.303.111.00 and 930.303.110.02.

Machined from 6061 T6 aluminium; features a replaceable threaded insert for the supplied bolt.

Fits all Porsche 915 transaxles 72-86 and 930 4 speed transaxles 76-88.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91530311100

您正在查看的产品与这些编号存在交叉引用关系

If you are rebuilding a Porsche 915 or 930 transmission it's likely the 3rd/4th shift fork is worn out.

Replacing factory part numbers 915.302.112.00 and 930.303.112.02 our part is made in house from 6061 T6 aluminum - and incorporates replaceable grade 10 hardware in the event the threads should strip.

Fits all 915 transmissions '72-'86 and all 930 transmissions '76-'88.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

91530211200

您正在查看的产品与这些编号存在交叉引用关系

Tensioning plate.



Fits:
Porsche 924 1978-1979 Only for 5-speed transmission
Porsche 911 G Turbo 1975-88 Only for 4-speed transmission

Click 'Zoom in' for large parts diagram.
Diagram ref no 21

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

93030212101

您正在查看的产品与这些编号存在交叉引用关系

This update will allow for use of the late style 915 main shaft seal and o-ring on early transmissions ('72-'75) where the seal installs from the inside and the guide tube is not removable.
The update is a also good repair for those whom have loose, damaged or worn out guide tubes.

** This requires machining to fit

The original is machined off and a custom steel tube is fitted. It's further retained from the inside of the diff case with a high quality snap ring and sealed with the factory o-ring.