前侧车顶支架

Bushing kit for camber plate and monoball.



For use with Rennline 964/993 Camber Plates and Monoball Strut Mounts

Bushing Kits for use with Rennline 964/993 Camber Plates and Monoball Strut Mounts. Kit is available in m12 or m14 sizes and includes 2 flat spacer bushings and 4 stepped bushings. These are replacement bushings which are only needed when swapping to struts with a different shaft diameter (These are included with the 964/993 front and rear upper monoball/camber plates).

Front Adjustable Camber Plate Top Mount Set - Sealed for Porsche 993/964 

SET OF 2.

Fits:
Porsche 964 / 993*

* For cars with factory Boge shocks please call for fitment details.

** For 993's with factory strut mounts, longer strut mount bolts (m8x25mm) are required. Fits Bilstein PSS9/10 Kits, KW suspension and Ohlins suspension by drilling the centre bearing a little larger.

Camber Plates/Strut Mounts - Under extreme conditions, such as road racing and autocross, negative camber is required to keep as much of the tire’s contact patch on the road as possible. Stock suspension mounts will not allow you to achieve the necessary amount of negative camber required for this type of performance driving. Sealed camber plates incorporate motorsports Teflon-lined spherical bearings and eliminate the indistinct feedback associated with factory rubber mounts.

- Drastically increased bearing life due to the integrated factory GT3 weather seals.
- Motorsports Teflon-lined spherical bearings.
- Rigid bearing mount, not clipped in like some products available.
- Can be used with all factory and aftermarket struts, Including factory non adjustable units.
- Longer stud lengths to allow for easy installation of strut bar.
- Fully rebuild-able
- CNC machined 6061 anodized aluminium construction with stainless steel hardware.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3602509641

您正在查看的产品与这些编号存在交叉引用关系

QuickChange™ front camber plate kit.
Sold per kit, 1 kit req'd per car.



Extend the range of camber adjustment and dial in your desired settings with ease.

These plates use high strength hardened steel spherical bearings and are direct replacements for the factory plates. The Teflon lined spherical bearings used in our kit are maintenance-free and require no supplemental lubrication. Included seals prevent contamination from water or grime, thus extending bearing life.

Fits:
Porsche 964 1990-94 / 993 1995-98 Front camber plate 14mm spacers

Fully Weather Sealed:
We've designed in weather seals on the top and bottom to keep dirt out and extend product life. This is the only camber plate suitable for street or extended track use. Dirt and water contaminate ordinary products and accelerate wear.

This camber plate is intended to be used with a non-factory upper spring perch and spring. This kit is suited to work perfectly with Von Coilover systems or other similar solutions.

Please note: please contact us if you wish to use this camber plate kit in conjunction with factory or lowering springs.

Ease of Camber Adjustment
Indices on the camber plate allow measured changes without setup tools.

Extended Caster
These plates deliver the same caster as the 993 for enhance camber gain when turning.

Improved Shock / Coilover Performance
Spherical bearings further improve performance. The spherical bearings pivot freely and eliminate the deflection that is inherent with the factory rubber bushings. This is important for two reasons;

– The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.

– The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2152202

您正在查看的产品与这些编号存在交叉引用关系

Rennline Front Adjustable Camber Plate Top Mount Set - Sealed. SET OF 2.

Fits:
Porsche 964 / 993*

* For cars with factory Boge shocks please call for fitment details.

** For 993's with factory strut mounts, longer strut mount bolts (m8x25mm) are required.

** For cars with KW CLUBSPORT struts, select the KW drop drown as it includes alternate hardware required for installation.

Camber Plates/Strut Mounts - Under extreme conditions, such as road racing and autocross, negative camber is required to keep as much of the tire’s contact patch on the road as possible. Stock suspension mounts will not allow you to achieve the necessary amount of negative camber required for this type of performance driving. Rennline’s Sealed camber plates incorporate FK motorsports Teflon-lined spherical bearings and eliminate the indistinct feedback associated with factory rubber mounts. Why are Rennline’s strut mounts the best ?

• Drastically increased bearing life due to the integrated factory GT3 weather seals.
• FK Motorsports Teflon-lined spherical bearings.
• Rigid bearing mount, not clipped in like some products available.
• Can be used with all factory and aftermarket struts, Including factory non adjustable units. Call for details.
• Longer stud lengths to allow for easy installation of strut bar.
• Fully rebuildable
• CNC machined 6061 anodized aluminum construction with stainless steel hardware.
• Available for front and rear

*Strut brace not included but is available separately.

For fitting information about this product Click Here

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

SB676974

您正在查看的产品与这些编号存在交叉引用关系