后控制臂

Adjustable lower control arms (lower wishbone)



Fits
Porsche 986 Boxster - Front and Rear
Porsche 996, 997 - Front and Rear
Porsche 991 - Front Only
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 981 Boxster and Cayman - Front and Rear
Porsche 718 Boxster and Cayman - Front and Rear

Set of 2 x Adjustable lower control arms - 1 pair, required per axle

Elephant Racing adjustable lower control arms provide the camber, caster and precision you need. Length adjustable similar to the factory GT3 control arms, but without the need for shims.

Quick and Easy Adjustments – No need to keep a stock of shims on hand, length is easily adjusted by rotating the center hex head. Rotate clockwise to expand or counter-clockwise to contract the arm length.Adjustments can be made within minutes. No shims to mess with. Perfect setup to make quick changes for the track.

Widen Track – Use in combination with our camber plates on the front, or our adjustable length arms upper control arms on the rear to widen the track. This allows you to achieve a wider track without altering the scrub radius as happens when using wheel spacers.

Heim Joint – Our spherical bearings eliminate the deflection associated with rubber bushings. These bearings maintain stable suspension alignment, and improve feedback.

Fully Weather Sealed – Proper boots at both the ball joint and heim joint ends to keep water and contaminants out for extended life. These arms are suitable for extended road and track use.

Camber Adjustment – Extended range of adjustment lets you achieve aggressive camber. Or you can dial it back to get a factory street alignment on lowered cars.

Caster Adjustment – Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms to correct for un-intended caster change that is caused by the extended arms. Rotate the center puck and bolt down to secure the setting.

The arms are fully rebuildable with replaceable heim and ball joints.

On 996, 997, & 991 Cars:
Center puck can be also used as a wheelbase adjuster on the rear to draw the wheels back to improve weight distribution. It is a great tuning aid for adjusting out understeer

Litronic Bracket – This bracket is required for cars that are originally equipped with the litronic headlights. This adapter bracket attaches to the headlight angle sensor.


相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180001

您正在查看的产品与这些编号存在交叉引用关系

Litronic Bracket for adjustable control arms.



Fits
Porsche 996 - Front & Rear with Litronic headlights
Porsche 997 - Front & Rear with Litronic headlights
Porsche 991 - Front & Rear with Litronic headlights

Porsche 986 - Front Only with Litronic headlights
Porsche 987 - Front Only with Litronic headlights
Porsche 981 - Front Only with Litronic headlights,

Price is for 1 and 2 Required per axle

This bracket is required for cars that are originally equipped with the Litronic headlights. This adapter bracket attaches to the headlight angle sensor.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180009

您正在查看的产品与这些编号存在交叉引用关系

Litronic Bracket for adjustable control arms.



Fits
Porsche 987 - Rear with Litronic headlights
Porsche 981 - Rear with Litronic headlights

Price is for 1 and 2 Required per axle

This bracket is required for cars that are originally equipped with the Litronic headlights. This adapter bracket attaches to the headlight angle sensor.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

218002

您正在查看的产品与这些编号存在交叉引用关系

BBi Autosport front/rear lower control arm kit for Porsche 996/997/991/987/981 except GT4
Fits cars with and without PASM



Features :

•   Improved two piece 996 GT3 lower control arm design
•   Stronger than cast motorsport Cup arms
•   Allows proper camber adjustment
•   Uses GT3 shims to adjust camber & lower control arm length (sold separately)
•   High-strength steel alloy spherical bearings, completely serviceable unlike the motorsports arms
•   Sealed monoball inner bearing
•   Allows easy access to inner arm hardware
•   Includes adjustable thrust arm bushings to adjust caster and wheelbase
•   A must have for all track and race enthusiast
•   Each kit includes pair of 2 arms
•   Fits both front and rear axles
•   Compatible with all 996/997/991/987/981 models except GT4

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

BBILOWRCNTRL9697

您正在查看的产品与这些编号存在交叉引用关系

ADJUSTABLE THRUST ARM BUSHING KIT (For vehicles equipped with Hydraulic Thrust Arm Bushings Only).
SET OF 4. FRONT AXLE ONLY



The RSS Adjustable Thrust Arm Bushing Kit will improve handling and response in 987. 997, 981, GT4, 991 GT3 variants, suspension systems and allows for additional caster adjustments. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.

AVAILABLE FOR ALL PORSCHE® 987,981, GT4, 997, 991 and 991 GT3, and 991 TURBO
NOT FOR 997 GT3/GT2

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

360

您正在查看的产品与这些编号存在交叉引用关系

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.



Fits
Porsche 991 GT3 OE Front Control Arms
Porsche 981 GT4 Front and Rear Control Arms
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,

Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing.
Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls. RSS Longer studs allow for more negative camber adjustment / gain vs. OE inner bushing. For camber shim kits see RSS Part # 308.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3-256

您正在查看的产品与这些编号存在交叉引用关系

RSS Lower Control Arm Adjusting Shim - Rear. 



Fits:
Porsche 991 GT3 / GT3 RS
Porsche 991 GT2 RS

Price: One Alignment Shim

RSS alignment shims are designed for use with factory or aftermarket 2-piece motorsport style control arms. Perfect for obtaining more negative camber and adjusting track width during setup.

Shims are available in a variety of sizes including 1mm, 2mm, 3mm, 5mm, 7mm, 10mm and 11mm.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

301

您正在查看的产品与这些编号存在交叉引用关系

RSS Tarmac series rear alignment / camber shim
Assortment Pack: (2 of each size) 1mm, 2mm, 3mm, 8mm 10mm.



Fits: Porsche OE 2-Piece rear lower control arm set.

Fits:
Porsche 991 GT3/GT3/RS


Made in the USA

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

397

您正在查看的产品与这些编号存在交叉引用关系

RSS XL TARMAC SERIES XL 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Rear Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits:
FOR REAR AXLE PORSCHE 986, 996, 997, 987, 981/982/718

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.
*** Note: 981 and 991 Models may require additional Front Litronic or Torque Vector Sensor Brackets.

RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers If you need assistance in identifying your suspension type please contact us. For specific fitment information refer to the "Chassis Fitment Guide and Lower Control Arm Fitment Notes" (See Images Below).

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS:
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength
steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS.

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS

RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

374

您正在查看的产品与这些编号存在交叉引用关系

REAR NON-ADJUSTABLE THRUST ARM BUSHING KIT. Rear Axle. Ideal for castor/length adjustable style thrust arms from other brands. for Porsche 986/996/997/981/982/718

SET OF 4. REAR AXLE ONLY

Brand:

The RSS Non-Adjustable Thrust Arm Bushing Kit will improve handling and response in suspension systems. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.

AVAILABLE FOR ALL PORSCHE® 986, 987, 996, 997, 981 MODELS INCLUDING TURBO & GT3 FOR NON-HYDRAULIC APPLICATIONS ONLY FOR HYDRAULIC APPLICATIONS.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

334

您正在查看的产品与这些编号存在交叉引用关系

后趾连杆锁定板套件。
2 件套



适合：
保时捷 996 C2、C4、C4S、Turbo、GT2、GT3
保时捷 997 C2、C2S、C4、C4S、Turbo、GT2、GT3
保时捷 986 Boxster / Boxster S
保时捷 987 Boxster / Boxster S
保时捷 987 Cayman / Cayman S
保时捷 981 Boxster / Boxster S
保时捷 981 Cayman / Cayman S / Cayman GT4
保时捷 991 C2、C2S、C4、C4S、Turbo、GT2、GT3
保时捷 982（718） Boxster / Boxster S
保时捷 982（718）Cayman / Cayman S

可选的 RSS 锁定板套件设计用于 RSS 可调后束/碰撞转向套件（零件编号 312） 。

该套件取代了在赛车和/或激烈驾驶条件下可能松动的工厂偏心螺栓。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

333

您正在查看的产品与这些编号存在交叉引用关系

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.

Brand:

Fits
Porsche 991 GT3  (not RS) OE Front Control Arms,
Porsche 981 GT4 Front and Rear Control Arms,
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,
Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing. Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls.

The Extra Long Monoball Housing Design (+15mm) allows for more negative camber adjustment / gain vs. standard aftermarket or OE inner bushings. The XL Design allows for proper stud engagement between inner and outer control arm with when running aggressive negative camber settings. For camber shim kits see RSS Part # 308.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3-307

您正在查看的产品与这些编号存在交叉引用关系

BBi Autosport StreetCup suspension package for Porsche 991 GT3 / GT3 RS



The BBi Street Cup Suspension Package improves the handling response of the vehicle by upgrading the factory springs with an improved linear rate springs and replacing the factory arms and links with the motorsport Cup version that uses spherical bearings.

Complete Package Includes:

2 Coilover Spring (Front)
2 Coilover Spring (Rear)
2 Coilover Helper Spring (Front)
2 Coilover Helper Spring (Rear)
2 Billet Monoball Lower Trailing Arm
2 Billet Monoball Upper Trailing Arm
2 Billet Monoball Upper Wishbone
2 Monoball Front Bearing Flange
2 Monoball Rear Bearing Flange
2 Upper Spring Rest
2 Lower Spring Rest
2 Adjustable Sway Bar End Link Front
2 Adjustable Sway Bar End Link Rear