前控制臂

ADJUSTABLE THRUST ARM BUSHING KIT (For vehicles equipped with Hydraulic Thrust Arm Bushings Only).
SET OF 4. FRONT AXLE ONLY



The RSS Adjustable Thrust Arm Bushing Kit will improve handling and response in 987. 997, 981, GT4, 991 GT3 variants, suspension systems and allows for additional caster adjustments. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.

AVAILABLE FOR ALL PORSCHE® 987,981, GT4, 997, 991 and 991 GT3, and 991 TURBO
NOT FOR 997 GT3/GT2

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

360

您正在查看的产品与这些编号存在交叉引用关系

RSS Front LCA litronic bracket.



RSS Part # 362 integrates the optional Litronic or Adaptive Headlamp systems with the Tarmac Series Lower Control Arms or OE 2pc Arms on :

Porsche 986 Front and Rear,
Porsche 987 Front (987 Rear See #364),
Porsche 997 Front and Rear,
Porsche 981 Front axle ( 981 Rear See # 387),
Porsche 991 Front (Except for GT3/RS)

Adapter Bracket for RSS Tarmac Series Rear Lower Control Arm. - 1 Per Car Axle (Located on front and rear drivers side axle, connects to OE Sensor Arm)

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

362

您正在查看的产品与这些编号存在交叉引用关系

RSS TARMAC SERIES XL (Extra Long) 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Front Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits:
FOR FRONT AXLE PORSCHE 986, 996, 997 GT3/RS, 997 GT2/RS

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.

RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers If you need assistance in identifying your suspension type please contact us. For specific fitment information refer to the "Chassis Fitment Guide and Lower Control Arm Fitment Notes" (See Images Below).

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS:
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength
steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS.

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS

RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

373

您正在查看的产品与这些编号存在交叉引用关系

RSS TARMAC SERIES XL (Extra Long) 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Front Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits:
FOR FRONT AXLE PORSCHE 987, 997/991 C2, C4, Turbo, 981/982/718

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.
*** Note: 981 and 991 Models may require additional Front Litronic or Torque Vector Sensor Brackets.

RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers If you need assistance in identifying your suspension type please contact us. For specific fitment information refer to the "Chassis Fitment Guide and Lower Control Arm Fitment Notes" (See Images Below).

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS:
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength
steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS

RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

372

您正在查看的产品与这些编号存在交叉引用关系

RSS TARMAC SERIES 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Front Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits front axle Porsche 987, 997/991 C2, C4, Turbo, 981/982/718

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.
** Note: 981 and 991 Models may require additional Front Litronic or Torque Vector Sensor Brackets.

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS
RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

361

您正在查看的产品与这些编号存在交叉引用关系

Front toe steer / bump steer kit XLARGE.



SET OF 2
replacement for 99634713104, 99634713103, 99134713100,

Fits:
FOR ALL Porsche 981, 982, GT4, 991 INCLUDING TURBO & GT3/GT3RS.

Also would fit Porsche 986, 996, 997, 987 that are running extreme amounts of negative camber or that have widened the front track width.

The RSS Adjustable Front Toe/Bump Steer XL Kit is designed for Porsche models that have been lowered. This kit will help minimize the suspension geometry change in the front of the vehicle. Allows for bump steer adjustment. Improves handling, feedback and control.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

371

您正在查看的产品与这些编号存在交叉引用关系

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.



Fits
Porsche 991 GT3 OE Front Control Arms
Porsche 981 GT4 Front and Rear Control Arms
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,

Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing.
Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls. RSS Longer studs allow for more negative camber adjustment / gain vs. OE inner bushing. For camber shim kits see RSS Part # 308.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3-256

您正在查看的产品与这些编号存在交叉引用关系

Lower Control Arm Adjusting Shims for Porsche Models



Price: One Alignment Shim

RSS alignment shims are designed for use with factory or aftermarket 2-piece motorsport style control arms. Perfect for obtaining more negative camber and adjusting track width during setup.

Shims are available in a variety of sizes including 1mm, 2mm, 3mm, 5mm, 7mm, 10mm and 11mm.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

300

您正在查看的产品与这些编号存在交叉引用关系

RSS Tarmac Series Lower Control Arm - Outer Ball Joint Pin Rebuild Kit. 1 Kit Per RSS Lower Control Arm (Fits: Part #s: 356, 357, 361, 372, 373, 374 and 366)



Includes:
1 x Tapered Stud,
1 x Upper Lock Nut,
1 x Lower Lock Nut and
4 x Roll Center Spacers/Washers.

1 Kit Per RSS Lower Control Arm (Fits: Part #s: 356, 357, 361, 372, 373, 374 and 366).

USER NOTE: A new 380 Kit should be installed once ball joint pin has been removed from hub. See Lower Control Arm Notes.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

380

您正在查看的产品与这些编号存在交叉引用关系

FRONT NON-ADJUSTABLE THRUST ARM BUSHING KIT. Front Axle. Ideal for castor/length adjustable style thrust arms from other brands. for Porsche 987/997/991/981/982/718/GT4

SET OF 4. FRONT AXLE ONLY



The RSS Non-Adjustable Thrust Arm Bushing Kit will improve handling and response of suspension system. Eliminates unwanted caster changes in both front or rear suspension under acceleration and deceleration.

AVAILABLE FOR ALL PORSCHE® 987, 997 (non GT#) 981, GT4, 991, 991 GT3/RS .

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

323

您正在查看的产品与这些编号存在交叉引用关系

Outer ball joint pin rebuild kit for Front bump RSS toe steer link/arm. Fits Part # 370 + 371



Kit includes: 1x Tapered Stud, 1 x Upper Lock Nut, 1 x Lower Lock Nut, 2 x Stud Spacers/Washers.

USER NOTE: A new 382 Kit should be installed once ball joint pin has been removed from hub.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

382

您正在查看的产品与这些编号存在交叉引用关系

Outer ball joint pin rebuild kit for RSS Rear toe steer link/arm , Fits part #312 and #301



Kit includes: 1x Tapered Stud, 1 x Upper Lock Nut, 1 x Lower Lock Nut, 2 x Stud Spacers/Washers

USER NOTE: A new 381 Kit should be installed once ball joint pin has been removed from hub

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

381

您正在查看的产品与这些编号存在交叉引用关系

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.

Brand:

Fits
Porsche 991 GT3  (not RS) OE Front Control Arms,
Porsche 981 GT4 Front and Rear Control Arms,
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,
Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing. Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls.

The Extra Long Monoball Housing Design (+15mm) allows for more negative camber adjustment / gain vs. standard aftermarket or OE inner bushings. The XL Design allows for proper stud engagement between inner and outer control arm with when running aggressive negative camber settings. For camber shim kits see RSS Part # 308.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3-307

您正在查看的产品与这些编号存在交叉引用关系

Spherical bearing inner GT3 monoballs for factory GT3 lower arm.

1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 - Front and Rear
Porsche 718 - Front and Rear
Porsche 991 - Front Only
Porsche 992 - Front Only
* Not For '12+ 991, 992 GT3/GT4

GT3 Street Inner Spherical Bearing Module

Unlike the factory rubber bushed GT3 inner control arms, our spherical bearings do not deflect under load.
They are fully weather sealed to keep out water and grit for extended life.

• Use in combination with factory GT3 street type control arm only
• Does not fit 991 GT3 or GT4 arms
• Easy Bolt-On
• Weather-sealed
• Sold as pair
• Front and Rear for 996, 997, 986, 987, 981, 718
• Front only on 991

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2180030

您正在查看的产品与这些编号存在交叉引用关系

Thrust Arm Spacer.



Kit includes: 4 spacers, two for each side. If using GT3 control arms front and rear order two kits.

Fits:
For Porsche 996 GT3 Control arms in 997/987

GT3 style adjustable lower control arms are a great upgrade for your watercooled 911, Cayman or Boxster. They give you a great range of camber adjustment, resulting in massively improved handling and tire wear characteristics. The 996 GT3 was the first to feature these arms, and because they are still available they are now the best bang-for-your-buck option on all watercooled cars. However, due to a difference in the height of the thrust arm bushing between the 986/996 and 987/997 chassis you will need these spacers to properly center the thrust arm on the lower control arm.

Track Control Arm and Bush Kit



Adjustable also uses our Black 95A material for both bushes for ultimate performance and is supplied with two CNC machined sleeves and spanners for on-car adjustment of both caster and camber, with the outer bush sleeve being made from a hard-anodized 2011 grade aluminium for increased corrosion and wear resistance.

PACK OF 2

This arm features suspension geometry tuning, with a caster increase of +/- 1.9° and camber adjustment of +/- 0.75°

OEM Part Number: 99134105304
OEM Part Number: 99734105304
OEM Part Number: 99134105321



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 inc. Turbo
Porsche 991 (2012-2019)
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005-2012)


CONTENTS (parts per pack):

2 x Short Adjustable Stainless Steel Sleeves
1 x C45 Spanner
2 x Stainless Steel Washers

Pre-assembled parts:
2 x Cast Aluminium Track Control Arms
2 x Outer Bushes
2 x Inner Bushes
2 x Long Adjustable Stainless Steel Sleeves
2 x Ball Joint Nuts

Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PF57K-1002G

您正在查看的产品与这些编号存在交叉引用关系

Adjustable track control arm with Black 95A shore rating bush fitted (SET OF 2) 



Adjustable also uses our Black 95A material for both bushes for ultimate performance and is supplied with two CNC machined sleeves and spanners for on-car adjustment of both caster and camber, with the outer bush sleeve being made from a hard-anodized 2011 grade aluminium for increased corrosion and wear resistance.

PACK OF 2

This arm features suspension geometry tuning, with a caster increase of +/- 1.9° and camber adjustment of +/- 0.75°

OEM Part Number: 99134105304
OEM Part Number: 99734105304
OEM Part Number: 99134105321

Fits:
FRONT 
Porsche 997 inc. Turbo
Porsche 991 (2012-2019)
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005-2012)



相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

3602409962G

您正在查看的产品与这些编号存在交叉引用关系

Track Control Arm and Bush Kit Adjustable uses our Black 95A material for both bushes for ultimate performance and is supplied with an offset outer sleeve and CNC machined inner sleeve with spanner to allow for on-car adjustment of both caster and camber, for quick and easy optimisation of your wheel alignment.

PACK OF 2

This arm features suspension geometry tuning, with a caster increase of up to 0.4° and camber adjustment of +/- 0.75°

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 GT2, GT3 & GT3RS
Porsche 997 inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Short Adjustable Stainless Steel Sleeves
1 x C45 Spanner
2 x Stainless Steel Washers

Pre-assembled parts:
2 x Cast Aluminium Track Control Arms
2 x Outer Bushes
2 x Inner Bushes
2 x Long Adjustable Stainless Steel Sleeves
2 x Ball Joint Nuts

Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PF57K-1001G

您正在查看的产品与这些编号存在交叉引用关系

Track control arm and bush kit uses a Black 95A inner bush and Purple 80A outer bush, providing a direct replacement alternative to worn OEM parts.

PACK OF 2

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 ALL inc GT2, GT3 & GT3RS
Porsche 997 MK2 ALL inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Cast Aluminium Track Control Arms
Pre-assembled parts:
2 x Outer Bushes
2 x Inner Bushes
2 x Short Stainless Steel Sleeves
2 x Long Stainless Steel Sleeves
2 x Ball Joint Nuts


Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PF57K-1001

您正在查看的产品与这些编号存在交叉引用关系

Track control arm and bush kit Black series

PACK OF 2

OEM Part Number: 98133105301
OEM Part Number: 99733104180
OEM Part Number: 99634105318



We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR Diagram reference 5R
Porsche 997 GT2, GT3 & GT3RS
Porsche 997 inc. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)


CONTENTS (parts per pack):

2 x Cast Aluminium Track Control Arms
Pre-assembled parts:
2 x Outer Bushes
2 x Inner Bushes
2 x Short Stainless Steel Sleeves
2 x Long Stainless Steel Sleeves
2 x Ball Joint Nuts

Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PF57K-1001BLK

您正在查看的产品与这些编号存在交叉引用关系

Track control arm and bush kit uses a Black 95A inner bush and Purple 80A outer bush with increased height to suit a wider range of models.



PACK OF 2

OEM Part Number: 99134105304
OEM Part Number: 99734105304
OEM Part Number: 99134105321

We're excited to introduce our new range of complete replacement Track Control Arm and Bush Kits for a number of Porsche models including 911 996, 997, 991, and Boxster / Cayman 718, 981, 986, 987.

Fits:
FRONT Diagram reference 2F
Porsche 997 inc. Turbo
Porsche 991 (2012-2019)
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005-2012)

CONTENTS (parts per pack):

2 x Cast Aluminium Track Control Arms
Pre-assembled parts:
2 x Outer Bushes
2 x Inner Bushes
2 x Short Stainless Steel Sleeves
2 x Long Stainless Steel Sleeves
2 x Ball Joint Nuts


Partnering with Chassis Technology Europe (CTE), a specialist in the manufacture of suspension and steering parts, we can now supply a high-quality cast control arm pre-assembled with our signature polyurethane bushes for a 'fit and forget' product, designed specifically for high performance and convenience of use with the added peace of mind of our Lifetime Warranty *.

Simply remove the old arm and refit!

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PF57K-1002

您正在查看的产品与这些编号存在交叉引用关系

轨道控制臂和衬套套件黑色系列



2 件装

OEM 零件编号：99134105304
OEM 零件编号：99734105304
OEM 零件编号：99134105321

我们很高兴推出适用于多款保时捷车型的全新完整替换横向控制臂和衬套套件，包括 911 996、997、991 和 Boxster / Cayman 718、981、986、987。

适合：
正面图参考 2F
保时捷 997 涡轮增压版
保时捷 991（2012-2019 年）
保时捷 718 Boxster/Cayman
保时捷 981 Boxster/Cayman
保时捷 987 Boxster（2005-2012）
保时捷 987C Cayman（2005-2012）


内容（每包零件数）：

2 个铸铝轨道控制臂
预组装部件：
2 x 外衬套
2 x 内衬套
2 x 短不锈钢套管
2 个长不锈钢套管
2 个球头螺母


通过与悬架和转向部件制造专家 Chassis Technology Europe (CTE) 合作，我们现在可以提供预先组装有我们标志性聚氨酯衬套的高质量铸造控制臂，从而打造出一款“装上即忘”的产品，专为高性能和使用方便而设计，并且我们还提供终身保修*，让您更加安心。

只需拆下旧臂并重新安装即可！

提供可调和不可调衬套选项，以适应不同的驾驶和性能要求。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PF57K-1002BLK

您正在查看的产品与这些编号存在交叉引用关系