Side section / Sub frame

制动软管支架，左前。



适合：
保时捷 996 C4S 2002>>
保时捷 997.1 C4*
保时捷 997.2 C4*
*不适用于配备 PCCB/选配 I450 的汽车

交叉支撑后悬架。
已售出 - 每辆车需要 2 个

#保时捷#

适合：
保时捷 996 C2 / C4 / C4S - 1997 至 2004 年
保时捷 996 Turbo - 2000 年至 2005 年
保时捷 996 GT3 - 1999 年至 2005 年
保时捷 997.1 C2 / C4 /C4S - 2005 至 2008
保时捷 997.1 涡轮 - 2007 年至 2008 年
保时捷 997 GT3 - 2007 年至 2012 年
保时捷 997.1 - 2005 年至 2008 年

单击“放大”查看大零件图。
图表参考号 10



相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99733108103

您正在查看的产品与这些编号存在交叉引用关系

Rear axle side section.



Fits:
Porsche 997.1 Carrera 2005-08
Porsche 997.2 Carrera 2009-12
Porsche 997.1 Turbo 2007-09
Porsche 997.2 Turbo 2010-13

Click 'Zoom in' for large parts diagram.
Diagram ref no 1

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99733105

您正在查看的产品与这些编号存在交叉引用关系

Silent block set for rear axle sub frame. Porsche 996, 997 
Standard street version.



Fits:
Porsche 997

Porsche 996

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

99633105XXX

您正在查看的产品与这些编号存在交叉引用关系

Solid subframe bushing set. 12 bushings in kit. 1 kit req'd per car.



Fits:
Porsche 996 / 997

Improved Handling and Precision
Our Rear Subframe Solid Bushing kit improves handling and precision by providing geometry correction for lowered cars and eliminating deflection. Porsche recognizes these performance benefits and uses a similar solid rear subframe mounting approach on the latest GT3 street and Cup racecars.

Replaces stock rubber bushings in the rear subframe of the Porsche 996 and 997 cars, raising the subframe into the chassis 6.5mm (.25 inch).

Geometry Correction
Lowering the 996/997 provides the benefits of lower center of gravity and improved appearance. Unfortunately lowering also causes the rear suspension members to angle down as the inner links drop with the chassis and the outer links remain at wheel upright height. This downward angle harms performance.

With the suspension members angling up towards the wheel the Roll Center is lowered which causes increased chassis lean, toe and camber curves are shifted and become less optimal, static toe and camber adjustments are shifted often exceeding the range of the stock adjusters.

Our kit raises the rear subframe .25 inches (6.5mm) to help reverse the negative effects of lowering. Suspension member angles are improved and performance is enhanced. Our upper bushing fits inside the subframe, eliminating the entire thickness of the upper rubber bushing for the greatest possible geometry correction achievable from bushings alone.

Eliminate Deflection
Stock rubber bushings compress and deform under heavy cornering, braking, and acceleration loads. The compliant rubber bushings allow the entire rear subframe shift about relative to the chassis. Rear camber and toe settings wander along with the subframe making the car less predictable, less stable in turns.

Our solid bushings replace the compliant rubber and do not deform under cornering loads, keeping the subframe in position and alignment true even under heavy cornering loads. The car becomes more predictable and easier to drive fast.

Build Quality
Each bushing consists of two pieces, an upper plug and lower puck. The plug is machined from solid aluminum with knurled edges for perfect fit.

Lower puck is machined from solid steel with zinc finish for protection.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2290035

您正在查看的产品与这些编号存在交叉引用关系