高性能制动软管
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
DOT 4
Having an extremely high boiling point and lower viscosity than required, it meets and greatly exceeds regulatory standards. Also suitable for vehicles with ABS.
Vapour Lock formation
This sort of habit leaves room for the Vapour Lock, the formation of vapour bubbles due to boiling of the brake fluid that replace the normal fluid and are compressed, thereby sending the brake pedal to its fill stoke (spongy pedal). The origin is incident in the porosity of the tubes that make up the braking circuit, which in time draw moisture into the fluid, drastically reducing the boiling point. The result is a reduced braking efficiency.
Brembo Premium Brake Fluid
Brembo Premium brake fluids have a higher boiling point that exceeds the standard, thus offering superior resistance to the Vapour Lock and ensuring braking efficiency even at low temperatures. With high anti-corrosion properties and resistance to oxidation, Brembo brake fluid also allows for long-term unaltered chemical/physical characteristics of the fluid in operating circuit; therefore, preserving its integrity.
Brake fluid DOT 4 LV (Low Viscosity) Textar.
Textar DOT 4 LV (Low Viscosity) is especially recommended for use in hydraulic brake and clutch systems of vehicles fitted with ESP, ABS and ASR with a high boiling point and outstanding performance at very low temperatures.
DOT 4 LV (Low Viscosity)
Dry Boiling Point ≥ 260° C
Wet Boiling Point ≥ 165° C
Viscosity at -40C < 750 mm2 /s
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut. <
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
Brake fluid is one of the most important fluids in a car as without it, stopping the vehicle safely would be impossible. The Brake fluid transmits the force exerted by the driver on the brake pedal onto the wheel brake.
To ensure perfect operation of the brakes, the brake fluid must be changed regularly during inspection or maintenance and tested with the correct brake fluid tester.
Brake fluid should be changed every two years.
The higher the DOT class, the higher the boiling temperature and wet boiling point. Higher DOT classes tend to allow longer maintenance intervals. The DOT standards are based on the American FMVSS-116 standard of the Department of Transportation (DOT).
Boiling Point and Viscosity
Dry Boiling Point - describes the property of the sealed new brake fluid. In this state, the brake fluid is almost anhydrous (substance containing no water). The dry boiling point is usually between 240 and 280°C.
Wet Boiling Point - determines the property of the brake fluid at the end of its life cycle, at a water content of 3.5% the fluid should be replaced. This defined wet boiling point must not be undercut.
Viscosity - describes the flow rate of the brake fluid. The lower the viscosity, the faster the brake fluid flows through the brake system, and the faster the brake signals are transmitted.
Important Notes
• Brake fluid is poisonous and a hazardous waste.
• Be careful when changing. The fluid weakens paints and plastics.
• It must not come into contact with eyes or skin. Always rinse spilled liquid with water.
• Do not pour the liquid into drinking water or mix with used oil.
• The colour of the brake fluid reveals nothing about its quality.
• Brake fluid should be stored in its original packaging and in a dry, cool and well-ventilated place.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
95002
您正在查看的产品与这些编号存在交叉引用关系
以 4 件套出售
适合:
保时捷 986 Boxster
保时捷 987 Boxster*
*可能需要张力/调整制动管线支架 99735533101
高性能制动管路 赛车专用的街道制动管路由最优质的软管制成,由编织不锈钢覆盖的 PTFE 内软管组成。不锈钢制动管路消除了普通橡胶制动管路经常出现的“海绵状”感觉,从而提供更灵敏、更牢固的制动踏板。
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
SPR0900-4C
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
以 4 件套出售
适合:
保时捷 986 Boxster
保时捷 987 Boxster*
*可能需要张力/调整制动管线支架 99735533101
高性能制动管路 赛车专用的街道制动管路由最优质的软管制成,由编织不锈钢覆盖的 PTFE 内软管组成。不锈钢制动管路消除了普通橡胶制动管路经常出现的“海绵状”感觉,从而提供更灵敏、更牢固的制动踏板。
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
SPR0900-4P
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
Sold as a SET OF 4
Fits:
Porsche 911 (996)
Porsche Boxster 986
Porsche 911 (997)
Black Diamond hoses are made as close to oe specification as possible and many applications come complete with line locators using high specification hose with stainless steel over braid to hold the strength of the hose.
Using Black Diamond braided brake hoses will give you a superbly firm and controllable brake pedal action.
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
DHK480
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
unique black plastic coating
Race proven technology for your road car
Fits
Porsche Boxster 986
Porsche 996
Porsche 997
Porsche GT3 1999-2011
Porsche 996 turbo
Porsche 997 turbo - Gen 1 and Gen 2
Performance brake hoses that are approved for road use, utilising the same hose & fitting technology used by race teams so have vastly improved pedal feel with a shorter, firmer brake pedal feel
Supplied with a unique jet-black finish, these are plated for increased life and undoubtedly look smart & professional with any caliper or wheel colour combination
Have a greater resistance to corrosion due to unique, plated stainless fittings with no age related performance drop-off
These hoses are easy to clean due to the black plastic coating and are compatible with DOT 3,4 and 5 brake fluids
Suitable for all ABS and non-ABS braking systems these hoses are probably the least expensive performance upgrade you can make and are especially effective at improved braking performance on older models
Conform to TUV / DOT and FMVSS106 certification
These hoses features a PTFE liner with stainless steel braid and are pressure tested to 200 bar
The fittings are high-grade stainless steel (303/304 grade) with a plated black coating
相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号,供比较之用。
BRAKELINEKIT
您正在查看的产品与这些编号存在交叉引用关系
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
Goodridge 不锈钢编织刹车线
Design911 全系列高性能保时捷 Goodridge 刹车线的库存商和经销商。 Goodridge 不锈钢编织刹车线已成为需要终极制动的专业赛车运动的标准。没有体积膨胀的空间,也没有橡胶刹车线造成的“糊状刹车”。
高效的制动系统可让您更快地进入弯道并加速加速。此外,当 G-Stop/Brakeline 套件制动软管与 ABS 制动系统一起使用时,它们几乎消除了制动踏板的“颤动”并显着缩短了制动距离。
- 刹车片及制动盘组件
- 标准制动盘
- 标准刹车片
- SPORTS 系列制动盘
- Brembo 标准制动器
- Brembo 赛车制动器
- TEXTAR 制动器
- PAGID 赛车制动器
- Zimmermann 制动器
- 高性能摩擦制动器
- Giro 开槽制动盘
- EBC 制动器
- 黑钻系列高性能制动器
- Rotinger 石墨系列
- 刹车片磨损传感器
- 刹车片减震垫片
- 制动钳螺栓/制动盘螺钉
- 销钉套件及导板
- 标准制动软管
- 制动钳和制动管路
- 制动钳
- 制动钳升级版
- 手刹蹄片
- 手刹线
- 制动盘盖板
- ABS | 速度传感器
- 制动钳密封件 | 活塞
- 制动伺服装置 | 助力器
- 制动主缸
- 制动液贮存箱
- 制动液
- 中央锁止轮毂
- 钛制刹车片防护罩
- 风管扰流板/导气罩
- DesignTek 制动器套件
- 自制制动器套件