Control Arms Rear

Adjustable caster bushing kit.
1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 Boxster and Cayman -Front Only
Porsche 991 -Front Only

Caster Tuning
Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms (GT3 control arms or eccentric monoballs) to correct for un-intended caster change that is caused by the extended arms.

Caster is also a great tuning aid for adjusting out understeer. Our Caster Adjusters let you tune the caster you need.

Two eccentric mounting points increase range of adjustment by up to 25mm. Choose from the inner bore for minor caster adjustments or the outer bore for extreme adjustments.

Rear Weight Bias
For the rear suspension, our Caster Adjuster can reduce rear overhang and rear weight bias. Cars with aggressive rear camber actually draw the wheels forward, increasing rear weight bias. Use our Caster Adjuster to compensate and even over-compensate for less rear weight bias than stock

Maintain Proper Alignment
Our Caster Adjuster is solid aluminum to hold alignment settings precisely. Stock rubber bushings compress under load, allowing alignment to wander and making the car less predictable. Our solid design eliminates compression, improves precision and maintains geometry true.

Functional Design Built To Last
Available for factory type lower control arms (wishbones) front and rear, including stock type arms and GT3 arms

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180011

The product you are viewing cross references to these numbers

Adjustable lower control arms (lower wishbone)



Fits
Porsche 986 Boxster - Front and Rear
Porsche 996, 997 - Front and Rear
Porsche 991 - Front Only
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 981 Boxster and Cayman - Front and Rear
Porsche 718 Boxster and Cayman - Front and Rear

Set of 2 x Adjustable lower control arms - 1 pair, required per axle

Elephant Racing adjustable lower control arms provide the camber, caster and precision you need. Length adjustable similar to the factory GT3 control arms, but without the need for shims.

Quick and Easy Adjustments – No need to keep a stock of shims on hand, length is easily adjusted by rotating the center hex head. Rotate clockwise to expand or counter-clockwise to contract the arm length.Adjustments can be made within minutes. No shims to mess with. Perfect setup to make quick changes for the track.

Widen Track – Use in combination with our camber plates on the front, or our adjustable length arms upper control arms on the rear to widen the track. This allows you to achieve a wider track without altering the scrub radius as happens when using wheel spacers.

Heim Joint – Our spherical bearings eliminate the deflection associated with rubber bushings. These bearings maintain stable suspension alignment, and improve feedback.

Fully Weather Sealed – Proper boots at both the ball joint and heim joint ends to keep water and contaminants out for extended life. These arms are suitable for extended road and track use.

Camber Adjustment – Extended range of adjustment lets you achieve aggressive camber. Or you can dial it back to get a factory street alignment on lowered cars.

Caster Adjustment – Our Caster Adjuster allows you to tune this important setting that the factory left out. A must-have for cars that have extended lower control arms to correct for un-intended caster change that is caused by the extended arms. Rotate the center puck and bolt down to secure the setting.

The arms are fully rebuildable with replaceable heim and ball joints.

On 996, 997, & 991 Cars:
Center puck can be also used as a wheelbase adjuster on the rear to draw the wheels back to improve weight distribution. It is a great tuning aid for adjusting out understeer

Litronic Bracket – This bracket is required for cars that are originally equipped with the litronic headlights. This adapter bracket attaches to the headlight angle sensor.


Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180001

The product you are viewing cross references to these numbers

BBi Autosport adjustable rear toe kit



Fits
Porsche 981 Boxster
Porsche 981 Cayman

Features :

•   Provides additional rear toe adjustment
•   OEM link is non-adjustable and eccentric bolt provides limited adjustment range, causing excessive tire wear and handling issues.
•   Helps maintain proper rear end suspension geometry
•   Fits rear axle
•   Each Kit Includes Pair of 2 Links

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

BBITOE981

The product you are viewing cross references to these numbers

Track control arms with adjustable bushings.



Fitted with Black 95A material for both bushes for ultimate performance and is supplied with an offset outer sleeve and CNC machined inner sleeve to allow for on-car adjustment of both caster and camber, for quick and easy optimisation of your wheel alignment.  (tools or spanner not included)  These arm features suspension geometry tuning, with a caster increase of up to 0.4° and camber adjustment of +/- 0.75°

OEM Part Number: 98133105301, 99733104180, 99634105319

Fits:

FRONT
Porsche 997 GT2, GT3 & GT3RS
Porsche 986 Boxster (1997-2004)
Porsche 996 (1997-2005)

REAR
Porsche 997 GT2, GT3 & GT3RS
Porsche 997 incl. Turbo
Porsche 718 Boxster/Cayman
Porsche 981 Boxster/Cayman
Porsche 986 Boxster (1997-2004)
Porsche 987 Boxster (2005-2012)
Porsche 987C Cayman (2005 - 2012)
Porsche 996 (1997-2005)

Please note: you will need 997 front fork arms to accommodate the adjustable bushes as they are wider than standard bush. 
When you add this item to the basket you will be prompted with mandatory product you will need to add as well.

Both Adjustable and Non-Adjustable bush options are available to suit differing driving and performance requirements.

Please click 'Zoom in' to view the diagram (No 21)

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3602409961G

The product you are viewing cross references to these numbers

Litronic Bracket for adjustable control arms.



Fits
Porsche 996 - Front & Rear with Litronic headlights
Porsche 997 - Front & Rear with Litronic headlights
Porsche 991 - Front & Rear with Litronic headlights

Porsche 986 - Front Only with Litronic headlights
Porsche 987 - Front Only with Litronic headlights
Porsche 981 - Front Only with Litronic headlights,

Price is for 1 and 2 Required per axle

This bracket is required for cars that are originally equipped with the Litronic headlights. This adapter bracket attaches to the headlight angle sensor.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180009

The product you are viewing cross references to these numbers

Litronic Bracket for adjustable control arms.



Fits
Porsche 987 - Rear with Litronic headlights
Porsche 981 - Rear with Litronic headlights

Price is for 1 and 2 Required per axle

This bracket is required for cars that are originally equipped with the Litronic headlights. This adapter bracket attaches to the headlight angle sensor.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

218002

The product you are viewing cross references to these numbers

Lower wishbone central bushing removal and installation tool.

1 x tool required



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 Boxster and Cayman -Front Only
Porsche 991 -Front Only

Simplify the installation process of Monoball products and replacement bushings.

Our two piece cup and piston tools allow for simple bushing extraction and insertion without removal of the wheel carriers or control arms. No need to use a shop press. The tools are designed to precisely fit the bushing circumference, preventing accidental damage to the bushing and ensuring proper installation.

We have tools for the LCA central bushings, the rear upright LCA bushings, and the rear upright shock mount bushings.

Front and rear control arms on the 996, 997, 986, 987, & 981
Front Lower Control Arm only on 991

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2260019

The product you are viewing cross references to these numbers

RSS Lower Control Arm Kit for Porsche Models .
Type: None Adjustable Thrust Arm Bushing



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Price: Set of Two Control Arms plus 2 x 1mm/2mm/3mm/7mm Shims.

RSS Tarmac Series Control Arms are manufactured from 6061 aerospace grade billet aluminum. This allows for a more uniform molecular structure
at every point of the arm over the cast motorsports arm giving the customer a more durable and inherently stronger part. Manufacturing from billet
aluminum rather than casting results in less impurities in the metal.

• Completely serviceable - for the extreme, repetitive track-day participant, our high-strength steel alloy spherical bearings (with a friction reducing /longevity increasing Teflon liner) can be replaced unlike the motorsports arm, in which case the customer will have to buy a new set of arms if the spherical bearings are worn.
Additionally, anodized surfaces and zinc-plated steel parts allow for better corrosion resistance against the elements.

• Adjustable suspension geometry - adjust dynamic camber values and roll center heights with our unique zinc-plated steel bushings.

• Solid monoball control arm ends offer a more responsive suspension over the factory one-piece rubber-injected control arm (also uses the same high
strength steel alloy spherical bearing found in our control arm monoball kit).

• Unique design provides more gusseting over the motorsports arms for added strength and aesthetically appealing looks.

Please Check Fitting Guide Before Ordering Click Here

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

357

The product you are viewing cross references to these numbers

RSS Lower Control Arm Kit for Porsche Models.
Type: None Adjustable Thrust Arm Bushing



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Price: Set of Two Control Arms plus 2 x 1mm/2mm/3mm/7mm Shims.

RSS Tarmac Series Control Arms are manufactured from 6061 aerospace grade billet aluminum. This allows for a more uniform molecular structure
at every point of the arm over the cast motorsports arm giving the customer a more durable and inherently stronger part. Manufacturing from billet
aluminum rather than casting results in less impurities in the metal.

• Completely serviceable - for the extreme, repetitive track-day participant, our high-strength steel alloy spherical bearings (with a friction reducing /longevity increasing Teflon liner) can be replaced unlike the motorsports arm, in which case the customer will have to buy a new set of arms if the spherical bearings are worn.
Additionally, anodized surfaces and zinc-plated steel parts allow for better corrosion resistance against the elements.

• Adjustable suspension geometry - adjust dynamic camber values and roll center heights with our unique zinc-plated steel bushings.

• Solid monoball control arm ends offer a more responsive suspension over the factory one-piece rubber-injected control arm (also uses the same high
strength steel alloy spherical bearing found in our control arm monoball kit).

• Unique design provides more gusseting over the motorsports arms for added strength and aesthetically appealing looks.

Please Check Fitting Guide Before Ordering Click Here

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

358

The product you are viewing cross references to these numbers

Rear adjustable lower toe control arms.



Fits
Porsche 981 Boxster and Cayman
Porsche 981 GT4

Set of 2 x adjustable toe control rod ends

Lowered 966,997, Boxsters and Caymans run out of rear toe adjustment range. Our Adjustable rear toe links extend the range of adjustment and add bump steer correction.

Adjustable Length – Threaded double adjuster for easy toe settings.

Angled Head – Lower the car and the toe links angle down. This shifts the ball stud from its center and limits the available range of articulation.
We solve this problem by angling the head to move the stud back towards the center of its range of articulation at static ride height.

Bump Steer Adjustable – 986 and 987 version have built in bump steer adjustment that lets you dial in a minimal bump steer curve.

Fully Weather Sealed – Proper boots at both the ball joint and heim joint ends to keep water and contaminant out for extended life.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180020

The product you are viewing cross references to these numbers

Rear adjustable thrust arm kit for Porsche 981 Boxster and Cayman



Fits
Porsche 981 Boxster
Porsche 981 Cayman

Features :

•   Connects the Lower Control Arm to the subframe
•   Provides precision caster adjustability
•   Spacers included for setting stock or anti-squat and anti-dive configurations
•   Each Kit Includes Pair of 2 Links
•   Fits rear axle

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

BBITHRUST981

The product you are viewing cross references to these numbers

Rear control arm monoball kit. 1 kit, req'd per car.
Ball Joints.



Fits:
Porsche 993 1995-98
Porsche 996 1998-04
Porsche 997 2005-12
Porsche 986 Boxster 1997-04
Porsche 987 Boxster 2005-12
Porsche 981 Boxster 2012-16
Porsche 987C Cayman 2005-12
Porsche 981C Cayman 2014-16

Complete kit for the rear 993, 996/997, Boxster & Cayman toe control arms. Includes weather-sealed monoball cartridge replacements for the bushings of the rear toe control arms (track rod).
Includes 2 cartridges.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2260014

The product you are viewing cross references to these numbers

Adapter Bracket for RSS Tarmac Series Rear Lower Control Arm.


Fits:
Porsche 981 Boxster / Boxster S
Porsche 981 Cayman / Cayman S / Cayman GT4

The RSS Adjustable Toe Steer Kit is designed for 996 and 997 models that have been lowered.

The RSS Litronic Headlight Adaptor Bracket for Rear Lower Control Arms integrates the optional Litronic or Adaptive Headlamp systems with the Tarmac Series Lower Control Arms on 981 Boxster / Cayman.

1 Per Car (Located on rear drivers side axle, connects to OE Sensor Arm).

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

387

The product you are viewing cross references to these numbers

ADJUSTABLE THRUST ARM BUSHING KIT (For vehicles equipped with Hydraulic Thrust Arm Bushings Only).
SET OF 4. FRONT AXLE ONLY



The RSS Adjustable Thrust Arm Bushing Kit will improve handling and response in 987. 997, 981, GT4, 991 GT3 variants, suspension systems and allows for additional caster adjustments. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.

AVAILABLE FOR ALL PORSCHE® 987,981, GT4, 997, 991 and 991 GT3, and 991 TURBO
NOT FOR 997 GT3/GT2

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

360

The product you are viewing cross references to these numbers

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.



Fits
Porsche 991 GT3 OE Front Control Arms
Porsche 981 GT4 Front and Rear Control Arms
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,

Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing.
Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls. RSS Longer studs allow for more negative camber adjustment / gain vs. OE inner bushing. For camber shim kits see RSS Part # 308.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3-256

The product you are viewing cross references to these numbers

Lower Control Arm Adjusting Shims for Porsche Models



Price: One Alignment Shim

RSS alignment shims are designed for use with factory or aftermarket 2-piece motorsport style control arms. Perfect for obtaining more negative camber and adjusting track width during setup.

Shims are available in a variety of sizes including 1mm, 2mm, 3mm, 5mm, 7mm, 10mm and 11mm.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

300

The product you are viewing cross references to these numbers

RSS Tarmac Series Lower Control Arm - Outer Ball Joint Pin Rebuild Kit. 1 Kit Per RSS Lower Control Arm (Fits: Part #s: 356, 357, 361, 372, 373, 374 and 366)



Includes:
1 x Tapered Stud,
1 x Upper Lock Nut,
1 x Lower Lock Nut and
4 x Roll Center Spacers/Washers.

1 Kit Per RSS Lower Control Arm (Fits: Part #s: 356, 357, 361, 372, 373, 374 and 366).

USER NOTE: A new 380 Kit should be installed once ball joint pin has been removed from hub. See Lower Control Arm Notes.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

380

The product you are viewing cross references to these numbers

RSS XL TARMAC SERIES XL 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Rear Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits:
FOR REAR AXLE PORSCHE 986, 996, 997, 987, 981/982/718

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.
*** Note: 981 and 991 Models may require additional Front Litronic or Torque Vector Sensor Brackets.

RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers If you need assistance in identifying your suspension type please contact us. For specific fitment information refer to the "Chassis Fitment Guide and Lower Control Arm Fitment Notes" (See Images Below).

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS:
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength
steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS.

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS

RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

374

The product you are viewing cross references to these numbers

REAR NON-ADJUSTABLE THRUST ARM BUSHING KIT. Rear Axle. Ideal for castor/length adjustable style thrust arms from other brands. for Porsche 986/996/997/981/982/718

SET OF 4. REAR AXLE ONLY

Brand:

The RSS Non-Adjustable Thrust Arm Bushing Kit will improve handling and response in suspension systems. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration.

AVAILABLE FOR ALL PORSCHE® 986, 987, 996, 997, 981 MODELS INCLUDING TURBO & GT3 FOR NON-HYDRAULIC APPLICATIONS ONLY FOR HYDRAULIC APPLICATIONS.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

334

The product you are viewing cross references to these numbers

Rear Toe Link Locking Plate Kit.
SET OF 2



Fits:
Porsche 996 C2, C4, C4S, Turbo, GT2, GT3
Porsche 997 C2, C2S, C4, C4S, Turbo, GT2, GT3
Porsche 986 Boxster / Boxster S
Porsche 987 Boxster / Boxster S
Porsche 987 Cayman / Cayman S
Porsche 981 Boxster / Boxster S
Porsche 981 Cayman / Cayman S / Cayman GT4
Porsche 991 C2, C2S, C4, C4S, Turbo, GT2, GT3
Porsche 982 (718) Boxster / Boxster S
Porsche 982 (718) Cayman / Cayman S

The optional RSS Locking Plate Kit is designed for use with RSS Adjustable Rear Toe/Bump Steer Kit (Part# 312).

This kit replaces the factory eccentric bolt which can come loose under racing and/or aggressive driving conditions.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

333

The product you are viewing cross references to these numbers

RSS Tarmac series adjustable rear toe steer kit.
SET OF 2 Replacement for 98133104580



Fits:
Porsche 981 Cayman GT4 3.8L 2015 - 2017

The RSS Adjustable Rear Toe Steer Kit is designed for Porsche GT4 models that have been lowered or have aggressive negative camber settings.

This kit will help minimize the suspension geometry change in the REAR of the vehicle.

Allows for toe adjustment at the toe steer arm giving the ability to make adjustments independent of the factory eccentric bolts which may not offer sufficient adjustment.

Greatly improves handling and feedback.
Eliminates rubber bushing deflection.
For off road use only.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

302

The product you are viewing cross references to these numbers

Porsche GT4 Torque Vector/Litronic Sensor Bracket Set for Rear XL Inner Monoball #3-307.

Brand:

Fits:

Torque Vector/Litronic Sensor Bracket Set (For use with Rear XL Inner Monoball #3-307). Adapts the XL Inner Monoballs for use with OEM Torque Vectoring and Litronic System Sensors.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

388

The product you are viewing cross references to these numbers

Inner Spherical Bearing (Mono-ball) End Kit: SET OF 2.

Brand:

Fits
Porsche 991 GT3  (not RS) OE Front Control Arms,
Porsche 981 GT4 Front and Rear Control Arms,
Porsche 986, 987, 996, 997 with GT3/RS OE Front or Rear Split Control Arms,
Fits any RSS Tarmac Series Lower Control Arm or replaces any OE Porsche Split Arm Inner Bushing. Provides a Bolt On Mono-Ball Performance Solution replacing rubber mounted OE inner mono-balls.

The Extra Long Monoball Housing Design (+15mm) allows for more negative camber adjustment / gain vs. standard aftermarket or OE inner bushings. The XL Design allows for proper stud engagement between inner and outer control arm with when running aggressive negative camber settings. For camber shim kits see RSS Part # 308.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3-307

The product you are viewing cross references to these numbers