专业工具

TDC indicators for Porsche 911



To ensure the utmost in timing precision, the true TDC of all engines should be checked to confirm the accuracy of the pulley TDC mark in relation to the real TDC. This tool screws into the spark plug hole and gives a mechanical indication of where the piston is in relation to the pulley/crankshaft. By rotating the crankshaft and touching/bumping the piston against the dead stop BTDC, and then rotating the engine in the opposite direction and touching/bumping the piston again against the dead stop ATDC, recording both measurements on a degree wheel, the pulley, or our DigiDix- SR095, you can calculate pure TDC.

Available for either 12mm or 14mm spark plug holes.

Sold separately.

Through bolt o-ring installer for Porsche 911



Installing O-rings on the through bolts for a 911 engine case often slices the rings on the threads of the bolt, leading to ripped seals at best, or a leaky engine at worst. Use this cap to protect the O-ring and to insure a factory quality seal. Precisely machined from quality brass.

Stomski Racing SR024 Through bolt o-ring installer with sleeve for Porsche 911



Based on the factory P9511 tool, STOMSKI RACING's version of this tool incorporates a brass cap and a double-ended stainless steel sleeve to install the o-rings on the crankcase through-bolts of the 3.6 and later cases (but possibly can be used on some other 911 engines). By using the included brass cap to protect the delicate o-ring from getting cut on the threads of the bolt, you then use the "thin" end of the sleeve to slide the o-ring over the brass cap onto the shank of the through-bolt. Once the o-ring is clear of the threads, remove the SR024 brass cap and flip the SR024 stainless steel sleeve over and use the blunted end to securely and gently seat the o-ring in the recess on the 3.6 case.

Time-sert spark plug M14 x 1.25 deep hole kit



The perfect compliment for our SR130, Time-Sert's M14x1.25 Deep Hole Kit contains a step tap, wrench, seat cutter, and insert driver.

Inserts shown on the image are not included and are sold separately.

Time-Sert™ thread repair kit for SR065/SR067/SR068 for Porsche 911 / Boxster / 996 / 997



For exhaust port studs on 911, Boxster, 996/997 or GT3 heads where the threads have been pulled, or to recover from an already improper repair, we have developed this Time-Sert(tm) kit so you may use our SR065, SR067, SR068 or SR069 tools to insert a Time-Sert and save an otherwise ruined head. In addition to the standard Time-Sert(tm) parts (short P drill, counter-bore, tap, insert tool, and 5 short inserts), our kit also includes a full length P drill, two drill jigs/bushings to guide the P drill and tap in our SR065, SR067, or SR068 fixtures, 5 full length inserts, and 5 studs.

Time-Sert(tm) is a registered trademark of TIME FASTENER COMPANY

Timing chain strap / support for Porsche 911



When assembling the case halves on the 911 engine STOMSKI RACING's SR222 Timing Chain Strap will prove instrumental in supporting the chain to allow easier mating of the halves. Proper length, radius bend, tension, and quality steel insure that this tool will provide reliable and consistent support for all your engine builds.

Fits
• SR222 for all 911 engines

Transmission selector rod holding plate for Porsche 911



For holding the selector rods when adjusting and tightening the selector forks on the 901/911 (SR260) or the 915 transmissions (SR260A).

Precision CNC machined from extremely stable Delrin to insure accuracy now and after years of use.

Sold separately.

Valve lash adjuster fixture for Porsche 911



The established method of setting valve lash with a feeler gauge often provides for a "close enough" result and rarely provides for accurate, consistent, and easy to obtain precision. STOMSKI RACING's new version of an old-standby takes the "feel" out of setting valves and provides absolute precision, speed, ease of use, and consistency. By conveniently mounting a travel indicator over the adjuster of the rocker arm, STOMSKI RACING's 911 Valve Lash Adjuster allows you to quickly and accurately set and confirm the actual valve lash without settling for "close enough" or wondering whether your feel is consistent while trying to contort a feeler gauge into the far reaches of the 911 engine.

The SR097 is precision machined from 6061 aluminum and anodized for years of service on all 911 engines including 964s and 993s. Also available are a range of dial indicators including metric, digital, and compact travel indicators for use in restricted areas (pictured).

PLEASE NOTE:  this tool does not come with the gauge

Rennline valve lash tool.



Fits:
Porsche 911 - 1965 to 1989
Porsche 964 - 1989 to 1994

Product Description

Valve lash adjustments on the air-cooled 911 engine can be a frustrating and time consuming experience, even for the seasoned Porsche mechanic.
Working in close, cramped quarters can make valve adjustments an unpleasant procedure.

Finally, there is a simpler, faster and more exacting way to adjust valve lash on all air-cooled Porsche 911 engines! From the professional mechanic to the owner/enthusiast, this easy-to-use device is made to last for many years and will prove to be a valuable addition to your 911 toolbox.

• Repeatable 0.1 mm (.004 in) lash clearance settings on every valve
• Saves time and provides more accurate over traditional feeler gauge methods
• Aluminum and steel construction
• Zinc plated finish provides corrosion protection
• Laser engraved markings
• Durable box with foam insert for safe storage