Engine Modifications & Upgrades

Rotates clockwise



Fits:
Porsche 911 - 1972 to 1989
Excluding 911 SC 3.0ltr

This distributor is made in the historical design of the original Bosch 3.0 RSR ignition distributor and combines the latest technology with an authentic look. 

The ignition map is easily and freely programmable via an app and Bluetooth. 

In addition, an immobilizer can be locked/unlocked with a PIN and a speed limiter can also be set easily via a smartphone. 

This version requires two 3-pin HKZ devices but it fits all engines from 1972 to 1989, so from the 2.4ltr to the 3.2 Carrera 

This ignition distributor rotates clockwise, so for all engines except 911 SC 3.0ltr

Clockwise rotation



Fits:
Porsche 911 - 1972 to 1989
Excluding 911 SC 3.0ltr

This distributor is made in the historical design of the original Magneti Marelli 2.8/3.0 RSR ignition distributor and combines the latest technology with an authentic look. 

It was installed at the factory on the 911 ST 2.5ltr and on the 2.8ltr 911 RSR and the ignition map is easily and freely programmable via an app and Bluetooth. 

In addition, an immobilizer can be locked/unlocked with a PIN and a speed limiter can also be set easily via a smartphone. 

This version requires two 3-pin HKZ devices but it fits all engines from 1972 to 1989, so from the 2.4ltr to the 3.2 Carrera 

This ignition distributor rotates clockwise, so for all engines except 911 SC 3.0ltr

替代博世 0280160262、0280160232、0280160215、保时捷 92811019802、92811019801、92811019800、92811019826（2.5 Bar 未连接真空管路）

这些调节器大多数都是原装的，已有近 40 年的历史，因此很容易发生泄漏或故障，从而导致各种运行和调整问题。它们很容易更换，尽管位于 3.2 升发动机歧管的前面有点麻烦。为了适应 3.2 Motronic 较低的工作燃油压力，我们使用了可调节燃油压力调节器。这种简单而优雅的设计使用钢制 O 形圈凸台密封适配器连接到歧管。

易于更换的燃油压力调节器。
燃油压力表或传感器的备用出口。
可调燃油压力调节器已使用博世044燃油泵进行了测试，但燃油流量上限尚未测试。

套件包括：

• 保时捷 911 3.2 Carrera / 早期 928（非 CIS） OEM 配件套件 - SPA 可调燃油压力调节器
• 燃油压力调节器主体 x 1
• 2.0 至 5.0 可调燃油压力调节器，而不是固定调节器 x 1
• 用于安装 OEM 软管和燃油导轨端部的适配器配件 x 2
• 软管尾部接头，用于安装工厂回流管 x 1
• ORB 插头 x 1

该套件必须使用可调节燃油压力调节器，因为博世不生产这种形式的标准 2.5 巴压力调节器。

请注意
其他配件和选件如燃油压力传感器或燃油压力表可根据要求提供。
我们还为 3.2 和 928 发动机开发了燃油压力阻尼器，请访问我们的网站了解产品详细信息。
燃油压力调节器安装后需要在汽车上进行调整和设置，以确保运行工况符合工厂规范。需要使用适合工厂燃油导轨的燃油压力表和配件才能完成此程序。调压器出厂时并未预设为 2.5 巴工作压力。

我们还可以为早期 944 提供解决方案，替换保时捷零件号 94411019801、博世零件号 0280160214、

Crafted from high-grade aircraft aluminum, our Porsche G-Model to 964 Billet Intake Runner delivers superior performance enhancements. Available in various cylinder head port diameters ranging from 34mm to 42.5mm, with options for standard injector sizes. 

Compatibility and Customization:
Tailored specifically to fit Porsche 2.7-3.2L engines, this intake runner enables seamless mounting of a Porsche 964/993 type intake. Unlike the 964/993's 3-bolt attachment, our design utilizes a 2-bolt M8 attachment for cylinder head placement.

Versatile Use and Configurations:
Compatible with standard rails or designed for use with the IslandWorks/Nuke system featuring a direct mount fuel regulator. 

Superior Craftsmanship and Finish:
Each runner boasts a natural machined finish, complemented by a base gasket insulator for optimal performance. To ensure that every set of intake runners arrives in style, they are shipped in a personalized color-of-the-day gift box as shown in the images.

Important Note:
This product requires a flat cylinder head seal (included in set) for superior heat insulation, deviating from the conventional seal type.

我们的钢坯和阳极氧化燃油导轨套件直接用螺栓固定到标准 3.2 进气歧管上。
在燃油轨上使用 O 形圈配件和 AN 6 JIC 配件，可以非常灵活地选择燃油软管布置。

复制工厂 964 系统或 993 系统，或者真正简化并使用死头系统。

导轨随附配件或插头的组合。

对于那些想要在售后 ECU 设置中调整、记录或使用保护策略的人来说，该套件可以非常轻松地将燃油压力传感添加到油轨中。

立即查看我们匹配的燃油压力调节器来完善您的燃油系统

套件包括：

• 燃油轨 x 2
• ORB 至 JIC 接头 x 4
• ORB 插头 x 2
• 阳极氧化支撑适配器 x 2
• 用于固定到工厂进气适配器的螺钉

请注意
配备工厂空调压缩机的汽车需要使用提供的塞子来封闭燃油导轨的后端，并选择常见的“死头”燃油软管布置。

＃适应＃

适合：
保时捷 964 - 1989 年至 1994 年
保时捷 993 - 1994 年至 1998 年
也适合
保时捷 911 - 1974 年至 1989 年配备 Adapt Motorsport 进气歧管适配器套件

有阳极氧化深银色或阳极氧化黑色可供选择

我们的钢坯和阳极氧化燃油导轨套件直接用螺栓连接到标准 964 / 993 进气适配器以及我们自己的适用于早期 2.7 升、3.0 升和 3.2 升发动机的 2 螺栓适配器套件。
在燃油轨上使用 O 形圈配件和 AN 6 JIC 配件，可以非常灵活地选择燃油软管布置。

复制工厂 964 系统或 993 系统，或者真正简化并使用死头系统。

导轨随附配件或插头的组合。

对于那些想要在售后 ECU 设置中调整、记录或使用保护策略的人来说，该套件可以非常轻松地将燃油压力传感添加到油轨中。

立即查看我们匹配的燃油压力调节器来完善您的燃油系统

套件包括：

• 燃油轨 x 2
• ORB 至 JIC 接头 x 4
• ORB 插头 x 2 个
• 用于固定到工厂进气适配器的螺钉

 

For Porsche 911 1964-89

OEM carrier mount units can experience fatigue failures at the welds from increased G loads while cornering and threshold braking at the track. The R-9055 Engine Carrier Mount counteracts these forces using a reinforced gusset design and high-quality materials.

Material: Type 304 stainless steel
Finish: Powder-coated in durable red finish
Weight: 3.8 lbs.
Models: Fits Porsche 911 ('64-'89).
Installation: Works with solid or rubber motor mounts; new mounting bolts supplied.
Miscellaneous: Replaces OEM Unit

For Installation instructions please CLICK HERE

Fits:
Porsche 911 / 911S 2.7Ltr - 1974 to 1978
Porsche 911 Carrera 3.0Ltr - 1976 to 1977
Porsche 911 SC - 1978 to 1983
Porsche 911 3.2 - Carrara 1984 to 1989

Modelled after the famous Campagnolo rally wheel, this is a stylish crank pulley and trigger setup for EFI conversions or to simply replace the factory steel pulley.

This Pulley uses a 36-1 toothed trigger setup best designed for hall effect sensors.

See our matching distributor drive reference and crank trigger sensor kit.  The best way to get sequential EFI on your engine.

Available for Pre-Order

Fits:
Porsche 911 - 1974 - 1989
Porsche 964 - 1989 to 1994
Porsche 993 - 1994 to 1998

911 used 2-Bolt type
964/993 uses 3-Bolt type

Please Note: 
The aluminium or plastic intake plenum(inlet manifold) is not included in the kit

Product Overview:

Inject power and precision into your vintage aircooled engine, now also for turbo or supercharged cars.

To be used when converting a G-Model 911 or a 964/993 engine to a turbocharged/supercharged engine with a 964 induction based Drive by Wire set-up

Conversion kit to a Porsche 964 based intake system to become a DBW (Drive by wire) intake based 74mm original Bosch throttle body (Sometimes referred to as 76mm) specifically executed all in CNC milled billet aluminum.

This is sold either with the intention to convert a Porsche 964/993 engine or to adapt and convert a 964 intake onto a G-model car when turbocharging (That sounds fun!).

Kit includes:

• Throttle body runner for 74mm throttle body in aluminum 
• Vacuum port on throttle body runner
• Original Bosch electronic throttle body
• Original Bosch MAP-T-sensor
• Connecting pipe out of aluminum replacing the resonance tube

Intake runners for the Porsche 911 G-model (2-bolt) or 964/993 (3-bolt) engine are made out of billet aluminium, 3D milled in a 5-axis machine. The port diameter indicated in the options is the diameter of the port in the cylinder head. 

The following parts are to be reused from your original 964 intake:
Rubber boots and clamps
The plenums (inlet manifolds)

Please Note:
Aluminium or plastic intake plenum is not included in the kit and neither are any of the items specifically listed as excluded above.

Fits:
Porsche 911 - 1974 - 1989

Please Note: 
The aluminium or plastic intake plenum(inlet manifold) is not included in the kit

Product Overview:

Inject power and precision into your vintage aircooled engine

Conversion kit for the 911 G-model to become a DBW (Drive by wire) intake based on the 964 induction and using the 74mm original Bosch throttle body (Sometimes referred to as 76mm). This is intended to breathe a bit more life into a classic G-model.

The kit includes

• Throttle body runner for 74mm throttle body
• Original Bosch electronic throttle body
• Original Bosch MAP-T-sensor
• Resonance tube
• Vacuum solenoid
• Connectors and hose
• Vacuum check valve
• Intake runners for the Porsche 911 G-model engine

Intake runners are made out of billet aluminium, 3D milled in a 5-axis machine. The port diameter indicated in the options is the diameter of the port in the cylinder head. Please note that these are the 2-bolt designs. 

To create a bit of intimacy between you and your engine we have included a bit of DIY work for you to convert your existing Porsche 964 intake into this version. 

The intake also exists in two versions - This is the premium version where the throttle body runner is milled out of a billet in aluminum. This is the pinnacle of craftmanship giving a very solid feel to the intake at a natural premium. Both options have the same performance and the same durability with the difference being the look and feel of a 5-axis machined piece as the very first thing you lay your eyes on when you open the engine decklid!

For both options the lower resonance tube is made from our usual modified PA12 in black.

The following parts will be reused from the 964 intake:

• Rubber boots and clamps
• Vacuum reservoir
• The aluminium or plastic plenums
• Resonance flap, actuator and shaft

Please Note: 
The aluminium or plastic intake plenum is not included in the kit and neither are any of the items specifically listed as excluded above.

Fits:
Porsche 911 - 1974 - 1989

Please Note: 
The aluminium or plastic intake plenum(inlet manifold) is not included in the kit

Product Overview:

Inject power and precision into your vintage aircooled engine

Conversion kit for the 911 G-model to become a DBW (Drive by wire) intake based on the 964 induction and using the 74mm original Bosch throttle body (Sometimes referred to as 76mm). This is intended to breathe a bit more life into a classic G-model.

The kit includes

• Throttle body runner for 74mm throttle body
• Original Bosch electronic throttle body
• Original Bosch MAP-T-sensor
• Resonance tube
• Vacuum solenoid
• Connectors and hose
• Vacuum check valve
• Intake runners for the Porsche 911 G-model engine

Intake runners are made out of billet aluminium, 3D milled in a 5-axis machine. The port diameter indicated in the options is the diameter of the port in the cylinder head. Please note that these are the 2-bolt designs. 

To create a bit of intimacy between you and your engine we have included a bit of DIY work for you to convert your existing Porsche 964 intake into this version. 

The intake also exists in two versions - this version is what we at Islandworks use with all other intakes, being a modified PA12 material from an industrial manufacturing process. Both options have the same performance and the same durability with the difference being the look and feel of a 5-axis machined piece as the very first thing you lay your eyes on when you open the engine decklid!
For both options the lower resonance tube is made from our usual modified PA12 in black.

The following parts will be reused from the 964 intake:

• Rubber boots and clamps
• Vacuum reservoir
• The aluminium or plastic plenums
• Resonance flap, actuator and shaft

Please Note: 
The aluminium or plastic intake plenum is not included in the kit and neither are any of the items specifically listed as excluded above.

This kit is a modern update to the 911 3.2 ignition system and brings the management of the car into the digital age to allow greater control over ignition and fueling.

The kit replaces your restrictive old fashioned air flow meter (barn door) with a modern map sensor managed by intake pressures.

The kit gives many driving benefits, better/smoother power delivery, better throttle response, eliminates lots of the low-down idle problems as it now uses a throttle position sensor and delivers more torque and BHP.

The kit is delivered ready to use with a PPT ignition map for the 3.2 standard engine management; however, the kit can be mapped for different cams and engine capacity increase.

Our latest kit now comes with an upgraded ECU and can run a wide band sensor (oxygen sensor).
Our kits include this capability but the sensor needs to be ordered separately.

While developing the upgraded ECU we have also changed our intake pipe; this now works with the factory airbox, gives a stock appearance in the engine bay and houses the map sensor and air temp sensor out of sight.

Kits includes:
• Delta 700 ECU
• 2 x Direct plug-in wiring looms
• Map Sensor and air temp sensor
• Air intake pipe, gasket, and bolts
• 6 Bosch injectors
• Vacuum pipe and T connector
• Throttle Position Sensor (TPS) and adaptor
• Support and service by PIE Performance
• Can Bus data connection tool

All our kits are 100% reversible, with no need to drill or alter components, we utilise what already exists

Patented technology that helps to increase air flow dramatically thus minimising air flow separation and reduces turbulence, resulting in higher volumetric efficiency.

This pristine technology with Knife-edged butterflies has improved inlet airflow and performance significantly. With the individual Throttle blades very close to the inlet valves, the engine and Throttle response are vastly improved. Along with this, we have also found an impressive increase in Horsepower, Torque, Driveability, and an incredible mechanical soundtrack.

Throttle Bodies come fully assembled and ready to bolt directly to the Cylinder Heads, with the following parts included:

• Anodised Aerospace Grade 6082/T6 Billet Aluminium "Shaft-less" Individual Throttle Bodies.
• Anodised Aluminium Inlets/Extensions suitable for flatdeck & ducktail models.
• Aluminium Ram Pipes & Assembly Tool.
• Throttle Position Sensor (TPS).
• Billet Aluminium Fuel Rails, Including PICO 377cc Fuel Injectors.
• Thermal Insulation Gaskets.
• Throttle Linkage System which connects directly to the existing OEM cable pick-ups.

you will need an EFI Installation & control kit which is not included

**please note
Race Mesh Ram Pipe Installation Kit is not included
this is extra product code 102-101-00086-01 The contents of these kits may vary, from the images provided

Engine case hardware set, titanium. 

Air-cooled Porsche 911 complete engine case hardware kit in high-strength high-purity Titanium alloy. 

Includes studs:
For 911
Ti Alloy studs x 57
12 Point Ti Alloy Lock Nuts x 57

For 964/993
Ti Alloy studs x 62
12 Point Ti Alloy Lock Nuts x 62

Porsche Motorsports employed titanium alloy engine case fasteners on many of their famous race cars, including the 904, 908, 935, 962, and some modern LMP2.

Fits:
Porsche 911 3.0ltr / 3.3ltr
Porsche 964
Porsche 993

Engine case through bolt set, titanium. 

Kit Contents
Ti Alloy Studs x 11
Ti Alloy Washers x 22
Ti Alloy 12-point Nuts x 11

Porsche Motorsports employed titanium alloy engine case fasteners on many of their famous race cars, including the 904, 908, 935, 962, and some modern LMP2.

Fits:
Porsche 911
Porsche 964
Porsche 993

Air-cooled Porsche 911 engine case through bolts in high-strength high-purity Titanium alloy. Including studs, washers, and  nuts.

Fits:
Porsche 911 / 911S 2.7ltr - 1974 to 1977
Porsche 911 SC - 1978 to 1983
Porsche 911 3.2 Carrera - 1984 to 1989

These adapters are used to modify the 2.7ltr / 3.0ltr / 3.2ltr Porsche 911 2 bolt cylinder head engines to the later 964 / 993 3.6ltr intake manifolds when converting to EFI.  

CNC machined on a 5 axis machine to our exacting tolerances and finish and anodised dark grey these are custom machined to match your port diameter and tapered to fit up to the 42mm inlet manifold port size.

The short adapor height maintains the overall height of the intake set, reducing the interference between the idle air control, the intake boot and the top of the engine bay insulation.  The factory plastic 3 bolt 964 stacks are too tall, and adding an adapter spacer would make the manifolds not fit at all.

This design permits the use of the standard 964 fuel injectors and fuel rails so positions the injector over the same relief in the intake port for the original CIS injector, ensuring proper atomisation of the injector spray into the intake port.

Key Features:
Precision machined from high grade aluminium
Anodized finish
Fits all Bosch 14mm O-ring fuel injectors
Fuel rail spacers are marked for easy cutting to suit long, medium or short injector types.

Kit Includes:
6 x CNC aluminium adapters
4 x Spacer/Posts for fuel rail 
4 x Bolts to suit standard full length Bosch injectors
12 x Nuts and washers 

Fuel rails not included in kit

34mm / 40mm / 41mm / 42mm adaptors are made to order. Please allow 4-5 weeks for delivery

Check out our fuel rail and fuel pressure regulator kits to make the perfect conversion set

Porsche 911 / 911S 2.7ltr - 1974 to 1977
Porsche 911 SC - 1978 to 1983
Porsche 911 3.2 Carrera - 1984 to 1989

These adapters are used to adapt the 2.7ltr / 3.0ltr and 3.2ltr Porsche 911 2-bolt cylinder head engines to take the 996 GT3 intake manifolds when converting to EFI.  
CNC machined our exacting tolerances and finish and anodised dark grey these are custom machined to match your port diameter and tapered to fit the 49mm bore of the GT3 inlet manifold.

The short height maintains the overall height of the intake set, reducing the interference between the idle air control valve, the intake boot and the top of the engine bay insulation.  

This design permits the use of the AMS fuel rails, and positions the injector over the same relief in the intake port for the original CIS injector, ensuring proper atomisation of the injector spray into the intake port.

Key Features:
Precision machined from high grade aluminium
Anodized finish
Fits all Bosch 14mm O-ring fuel injectors
Fuel rail spacers are marked for easy cutting to suit long, medium or short injector types.

Kit includes:

• CNC aluminium adapters x 6
• Spacer/Posts for fuel rail x 4
• Bolts to suit standard full length Bosch injectors x 4
• Nuts and washers for cylinder head studs x 12

44mm adaptors are made to order. Please allow 4-5 weeks for delivery

Check out our fuel rail and fuel pressure regulator kits to make the perfect conversion set.

我们新发布的燃油压力调节器支架安装在 Adapt Motorsport 燃油压力调节器上，安装在经典风冷发动机顶部的发动机通气盖螺栓上。
与保时捷 964 的做法相同。

它们由数控机床铝制成，并经过深银色阳极氧化处理，确实为任何经典的保时捷发动机舱增添了漂亮的外观。

请注意
套件中仅包含调节器支架和紧固件，所示调节器仅供参考，并不包含在内。

我们有一系列不同的调节器可供订购。

Oil backflow prevention kit. 

Sold as a complete kit. 1 necessary per car.

This oil backflow kit incorporates a check valve between the oil tank and engine which prevents smoking on start up for 911 and 930 models from 1973-89.

The issue is due to the oil tank sitting higher than the engine oil pump. Gravity creates a positive pressure on the pump and slowly fills the engine case with time. Once the car is started, the cars smokes heavily

Our complete kit includes a model specific check valve with upgraded suction hoses and stainless-steel clamps ready for installation.

为什么需要这个系统以及什么是曲轴位置传感器？

将经典保时捷改装为现代电子燃油喷射时，发动机控制单元 (ECU) 需要准确了解曲轴和凸轮轴在四冲程循环中的位置以及它们的旋转速度。这使得 ECU 能够正确计时每次火花和喷油器打开时间和持续时间。传感器指向曲轴皮带轮或飞轮，测量每个齿的脉冲。有一个缺失的齿，ECU 可以据此计算出曲轴相对于该缺失齿的位置。脉冲之间的时间给出了发动机的速度和变化率。

3.2 Carrera / 964 / 993 的飞轮上已经有一个传感器来测量曲轴位置，因此这些发动机只需要一个传感器来进行凸轮轴定位。该传感器安装在我们的模块主体中，测量驱动轴顶部的单个齿。由于它安装在分配器孔中，因此适合以发动机一半的速度运行，因此每 720 度会产生一次脉冲。通过这两个传感器，ECU 可以知道发动机在四冲程循环中的确切位置。现在，我们可以进行精确的顺序喷射和点火。

我们的套件使用高速数字霍尔效应传感器向发动机控制单元提供数字输出，这些传感器最好在 8V 下运行，大多数现代 ECU 都有专用于曲轴传感器的 8V 输出。

机加工铝制外壳和阳极氧化表面处理，配有免维护青铜衬套和终身密封滚柱轴承。这些传感器具有相当大的可调性，因此通常能够与其他优质供应商提供的现有曲柄滑轮和扳机轮设置一起使用。

Sync 1 传感器套件包括：

• 主体组装
• ZF 霍尔效应传感器，单齿，用于发动机循环传感 x 1
• 接线和连接器，带有用于连接到接线器的引脚和连接器。

当您在飞轮或皮带轮上已经有一些其他曲轴位置传感并且只需要添加发动机循环/同步传感器来完成您的顺序系统时可以使用。

该更换套件使用您自己的工厂分销商装备适合 OEM 分销商位置。只需从安装齿轮中拆下工厂分配器齿轮，连接到 ECU，微调曲柄触发盘的传感器气隙，在 ECU 中设置参考位置，您就可以获得最新顺序燃油和所需的所有传感功能。点火系统。该套件适用于 964、993 和涡轮分配器齿轮。

我们的气门弹簧经过专门设计和制造，适合保时捷应用的范围，而不是其他用途的弹簧。

它的固有频率比赛车用的原始弹簧更高，至少可以最大限度地减少赛道日情况下超速造成的损坏。

请注意
993 - 必须使用 8mm Ti 固定器和 Aasco 座椅

9mm 保时捷 911 钛合金气门弹簧固定器，适用于 9mm 气门。

可用于直接替换原厂保持架，但我们建议与 Aasco HP109 阀门弹簧和 HPSS 弹簧座结合使用。

12 件套

我们的气门弹簧经过专门设计和制造，适合保时捷应用的范围，而不是其他用途的弹簧。

它的固有频率比赛车用的原始弹簧更高，至少可以最大限度地减少赛道日情况下超速造成的损坏。

请注意
993 - 必须使用 8mm Ti 固定器和 Aasco 座椅