Distributor
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 6
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Basic
Distributor with Harness
Ignition Coil
CDI Module
The Gen 6 Perma-Tune for the 911SC comes in two models: Premium ignition module and the Basic ignition module. The Basic model is just that, basic: it performs only the same functions as the analog modules did back in the day. For the average street car, this may be all that is desired and of course is more affordable than the Premium model. It is however still a high performance part and is perfect for racing venues that do not allow programmable digital ignition systems. The Basic model has a smooth, more original looking housing than the Gen 5 cast housing.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCB
The product you are viewing cross references to these numbers
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 5
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Gen 5 Version
Distributor with Harness
Ignition Coil
CDI Module
The Generation 5 ignition boxes make diagnostics easier. The controller monitors and runs diagnoses programs automatically and is read by two coloured LED function lights the are viewable from underneath the unit. The diagnoses can also be done via a Bluetooth programming dongle which is available as a separate item.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCG5
The product you are viewing cross references to these numbers
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Fits
Porsche 911 SC 1978-1983
Porsche 911 turbo 3.3ltr 1978-1989 (US cars)
Perma-Tune Gen 6
Replace those tired and worn ignition components with this Ignition Kit
Contents of Kit
6 Pin CDI Module - Premium Version
Distributor with Harness
Ignition Coil
CDI Module
The Gen 6 Perma-Tune for the 911SC comes in two models:Premium ignition module and the Basic ignition module.
The Premium ignition module features a smooth, matt finish that mimics the patina of the original aluminum die cast part. It provides full control over RPM limit, mechanical advance timing, power output, multi spark function and has many other features that can be programmed using a computer, tablet or smart phone. This module comes preprogrammed for the Porsche 911SC so programming changes are optional. The Gen 6 Premium Perma-Tune makes diagnostics easier by providing onboard diagnostics that are automatically displayed by two coloured LED function lights. These LED lights assist in diagnosing both the vehicle and the ignition module. The green LED is a status indicator that can flash diagnostic fault codes. The red LED is a strobe light that flashes each time the coils fires in the same manner as a timing light. This LED is especially useful for detecting intermittent engine misfire caused by wiring or distributor problems. The LED function lights are mounted in the harness electrical connector and can only be seen when the module is powered up. There are three self-resetting overload protectors that assist in troubleshooting while protecting your Perma-Tune from damage. The overload protectors are hidden underneath the ignition module so they do not spoil the original look of the part. Refer to the Diagnostics section of this web site for more information about the diagnostics system and overload protectors.
Distributor
Replacing that worn out distributor has never been easier with the Perma-Tune Bespoke distributor for the 911SC 3.0L engine and other engines like the Porsche Turbo 930 that use the six pin ignition module. There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done. There is no way to make a mistake with this installation, the connectors will only plug in the right way. The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Ignition Coil
he Perma-Tune Black Ignition Coil is specifically designed to operate with all Perma-Tune modules to maximize the performance and service life of your Perma-Tune ignition module. It has the period correct look for the Porsche 911SC with a brown top and black body and will fit the original mounting bracket and wiring harness of the car.
The Black ignition coil is very rugged and can resist the heat and vibration that it will encounter on a classic car engine. Triple seals insure that the dielectric oil inside the coil will not leak out. The high Voltage tower is extra thick to resist arcing and will still fit the original spark plug wire boot. The internal components of the coil are designed to resist deterioration to provide a long life.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
IGNITIONKITSCP
The product you are viewing cross references to these numbers
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
Porsche 911 1978-89.
Fits:
Porsche 911 SC 1978-83
Porsche 930 3.0ltr 1975-77 (US cars only)
Porsche 930 3.3ltr 1978-89 (US cars only)
New Perma Tune GEN 6 unit.
Bespoke distributor for the 911SC 3.0ltr engine and other engines like the Porsche Turbo 930 that use the six pin ignition module (CDI) and CIS injection
6 pin CDI was used from 1978 - 1983 on 911 and 1978 - 1989 on the turbo
The Perma-Tune distributor is an exact fit, replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction.
Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor.
The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance, retard, vacuum and boost functions.
On Turbo cars the vacuum/boost timing control can is very prone to leaks and the vacuum switches and manifold boost valves connected to the can are failure prone as well.
When these parts fail, performance deteriorates and fuel is wasted. These parts are bypassed by connecting the manifold hose directly to the MAP sensor of the distributor.
It just doesn't get any easier than this.
The distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look. It is very common on the Porsche 911 cars to develop engine misfire problems due to the brittle and deteriorating green shielded wire between the ignition distributor and module.
The defective wiring is replaced at the same time the new distributor is installed which cures two ills at once.
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear.
Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune distributor.
There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done There is no way to make a mistake with this installation, the connectors will only plug in the right way.
The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
930602021DX
The product you are viewing cross references to these numbers
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
Fits:
Porsche 930 3.3ltr - 1978 to 1989 (EURO cars only)
New Perma Tune GEN 6 unit.
Bespoke distributor for the Porsche Turbo 930 that use the eight pin ignition module (CDI) and CIS injection
The Perma-Tune distributor is an exact fit, replacement part that will drop right into the engine. Setting the static timing is easy with the built in trigger point LED that lets you know when the rotor is pointing in the right direction.
Idle timing is set in exactly the same way as the factory manual indicates and the factory mechanical and vacuum curves are preprogrammed into the distributor.
The mechanical vacuum can is replaced with a reliable MAP sensor that is fully programmable to perform advance, retard, vacuum and boost functions.
On Turbo cars the vacuum/boost timing control can is very prone to leaks and the vacuum switches and manifold boost valves connected to the can are failure prone as well.
When these parts fail, performance deteriorates and fuel is wasted. These parts are bypassed by connecting the manifold hose directly to the MAP sensor of the distributor.
It just doesn't get any easier than this.
The distributor harness is made using the same vinyl sleeve loom construction as the original wiring for that factory original look. It is very common on the Porsche 911 cars to develop engine misfire problems due to the brittle and deteriorating green shielded wire between the ignition distributor and module.
The defective wiring is replaced at the same time the new distributor is installed which cures two ills at once.
Distributors wear out and rob your engine of the horsepower it was intended to produce. Worse yet, they can leave you stranded or even damage the crankshaft ring gear.
Forget about rebuilding an outdated distributor with hard to find parts when you can replace it with modern technology that looks original. Replacing that worn out distributor has never been easier with the Perma-Tune distributor.
There are no wires to cut and splice: the distributor has the electrical harness built in and features the original equipment compatible connectors for a plug and play installation. Simply unplug the car harness connector from the ignition module and plug it into the matching connector of the distributor harness. Then plug the distributor harness connector into the Perma-Tune module and done There is no way to make a mistake with this installation, the connectors will only plug in the right way.
The harness connector has built in diagnostics lights that tell you when the ignition system has power and when the ignition module is making sparks. The blue connector LED is a power indicator and the red connector LED is a strobe light that flashes each time the ignition system makes a spark, just like a timing light.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060210300
The product you are viewing cross references to these numbers
- Porsche 911 1978-1989 3.3L Turbo (930)
Fits:
Porsche 911 1970-89
Porsche 911 (930) Turbo 1975-89
Porsche 964 1989-94 all models
Porsche 993 1995-98 all models
Click 'Zoom in' for large parts diagram.
Diagram ref no 4
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160210201
The product you are viewing cross references to these numbers
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) GT2 1994-97
- Porsche 993 (911) TURBO S 1994-97
OEM products manufactured by the Original Equipment Manufacturer.
Fits:
Porsche 911 1970-89
Porsche 911 (930) Turbo 1975-89
Porsche 964 1989-94 all models
Porsche 993 1995-98 all models
Click 'Zoom in' for large parts diagram.
Diagram ref no 4
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160210201
The product you are viewing cross references to these numbers
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) GT2 1994-97
- Porsche 993 (911) TURBO S 1994-97
Fits:
Porsche 911 (930) Turbo 1984-89
Clck 'Zoom in' for large parts diagram.
Diagram ref no 26.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
93060242203
The product you are viewing cross references to these numbers
- Porsche 911 1978-1989 3.3L Turbo (930)
This shim kit has an oil-lite bronze shim to replace the fiber one and a selection of shims to get the correct vertical play in your 911 distributor. The correct vertical play is point one of a millimeter to point one five of a millimeter, or .1 mm to .15 mm.
The shaft pin is a solid peen in pin.
This is sold as a kit.
Fits:
Porsche 911 1974-89
Porsche 911 (930) Turbo 1975-89
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160200198
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1978-1989 3.3L Turbo (930)
Fits:
Porsche 911SC 2.7L, 3.0L 1975>>
Porsche 930 3.3L 1975-89
Click 'Zoom in' for large parts diagram.
Diagram ref no 18
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
91160906107
The product you are viewing cross references to these numbers
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1978-1989 3.3L Turbo (930)
- Air Mass/Flow Sensors
- Alternator / Generator
- Batteries & Chargers
- Cold Start Valve
- Distributor Cap
- Rotor Arms / Point Sets
- Relays / Fuses
- Ignition Coil
- Ignition Control Units
- Ignition Lead Sets
- Ignition Lead High Performance
- Injectors
- Starter Motors
- Fuel Pump
- Speed / Reference / Knock Sensors
- Wiring Harness / Cables
- Throttle Body