Ignition Control Units

6 pin CDI connector housing. 



Fits:
Porsche 911 - 1978 to 1989

6 pin CDI Connector Housing for Porsche 911.

This is a high quality reproduction part made from PA12 Nylon which is tough, durable, heat and chemical resistant. It is also an excellent insulator.

Please Note
Pins & wiring not included, this is only the empty housing.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200

The product you are viewing cross references to these numbers

Ignition Coil. Porsche 911 / 930



This coil is designed to replace the Marelli BAE202B ignition coil or Bosch 0221121001. It will work with the Porsche Perma-Tune ignition modules. It is intended to look like original equipment and is a high quality coil made in the USA.

Fits:
Porsche 911 1970-83 / 911 SC
Porsche 930 Turbo 3.0L 1975-77
Porsche 930 Turbo 3.3L 1986-89
Porsche 356 12v Only

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90160250200

The product you are viewing cross references to these numbers

6 Pin CDI Harness

This harness is designed to be a stand alone replacement wiring harness for the 911SC models using the 6 pin CDI system. Until now the only way to replace a damaged ignition harness on the SC models was to replace the entire engine harness. This is very expensive and time consuming to do. We have designed this harness to allow the mechanic to just replace the wiring harness that controls the ignition function of the vehicle. The harness will plug directly into the CDI Box, The Ignition distributor and coil. The only two connections that will require some plug dis-assembly are the 12V ignition connection at the rear fuse panel and the tachometer signal wire at the 14 pin plug connector. Both of these wires come with the correct connectors installed on the wires.

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93061205000

The product you are viewing cross references to these numbers

Ignition Starter Unit CDI 6 PIN.
(Bosch Ref 0227300004)

Classic Retrofit replacement CDI+ ignition offers you bespoke modern electronics in a standard looking package. The CDI+ unit requires no modifications to the original wiring harness or vehicle metalwork and is 'plug and play'.

The CDI+ is a direct replacement for the 3 pin and 6 pin Bosch units fitted to Porsche 911's between 1969 and 1983 (and turbo models to ~1988). All CDI+ units have a 48 MHz microprocessor onboard to control ignition timing.

Advanced Unit:
The advanced unit allows the adjustment/tuning of the ignition advance curve and other features by plugging in a laptop. This can be achieved by 'overlaying' a curve on top of the distributor weights/springs curve or by locking the distributor and replacing the curve completely. Either way, you can unlock the true potential of your engine by adjusting fuelling and having the ignition curve to match.

The CDI+ has all the features of the basic unit but allow more flexibility in adjustment:
-Fully programmable ignition advance curve.
-Hard RPM limiter with adjustable ignition cut schemes
-Soft RPM limiter with adjustable ignition retard
-Launch RPM limiter
-Double spark at all RPMs
-Max RPM tell tale
-Shift Light output
-Clutch pedal input
-Tacho calibration
-Upgradeable through firmware updates

Fits:
Porsche 911 1978-83
Porsche 930 3.3L 1978-89

For 911-CDI+ Ignition Manual CLICK HERE

For 911-CDI+ Dyno Test Results CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

93060270200

The product you are viewing cross references to these numbers