Engine Modifications & Upgrades

The incredible 997 Porsche Turbo is the most revolutionary and capable Porsche Turbo to ever come out of Germany. The already explosive power can be further increased with the new 997 Turbo IPD Intake Plenums.



The patented IPD Plenum design works exceptionally well with all forced induction applications and the 997 Turbo is no exception. Power and torque increases provided by the IPD plenum are impressive and stay over and above all factory power curves from launch to redline. Maximum power increases take place in the midrange where it's most needed and most critical.

Maximum horsepower gains range from 30 to 35 depending on vehicle condition and pre-existing mods. The 997 Turbo plenums deliver smooth and linear power with considerably quicker boost response creating a longer and more desirable power band. The Turbo plenums deliver reliable performance for both street and motorsport applications enhancing the already visceral Porsche Turbo driving experience.

Unlike the 996 Turbo the 997 Turbo requires an "adaptation" period that can be fully realized with either a series of hard pulls on the dyno or 10 to 50 miles of hard driving which of course IPD recommends only be performed on a closed circuit race track.

The 997 Turbo has an extremely sensitive ECU/DME making it prone to external environmental corrections so it is imperative that proper, adequate and consistent cooling be available when you dyno any of the 997 Turbos to get accurate and reliable dyno figures both before and after each test.

Installation of all Turbo Plenums is highly recommended to be performed by qualified and trained Porsche technicians.

Turbo customers looking to increase engine power without pushing the motorsport envelope to redline would best benefit from the 74mm IPD Turbo Plenum.

This version of the 997 Turbo plenum utilizes the factory 74mm throttle body and delivers impressive performance gains for both stock and slightly modified Turbos with exhaust and software.

The 74mm IPD Turbo Plenum is also designed to perform with the higher flowing IPD "Y" Pipe.

Fits:
Porsche 997 Turbo

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

97274.2

The product you are viewing cross references to these numbers

The revolutionary 997 Turbo IPD "Y" Pipe was built for the more demanding Turbo performance customer. This is not a cast reproduction of the factory Y pipe but a complete re-design from scratch, developed to deliver even greater air flow for both stock AND highly modified Turbos.



The factory Y pipe becomes restrictive when adding substantial power gains. The IPD "Y" Pipe has larger inlets and an optimized diversion area allowing for even greater power gains. This superior and more efficient design flows 126 more cfm than the factory Y pipe delivering the additional power needed to raise the performance bar on any Turbo.

Bigger isn't always better, and the IPD "Y" Pipe is designed to deliver optimum flow without being too large causing a loss in boost response. These "Y" Pipes can also be special ordered in custom powder coated colors and ceramic coatings or polished to improve the aesthetic appeal of your Turbo engine.

The IPD 997 Turbo Y Pipe is designed to be a direct replacement of the factory OEM Y Pipe. There are no modifications or fabrication required for installing the IPD Y Pipe. This is an easy and straight forward R & R (remove and reinstall) bolt on upgrade.

997.2 Turbo Hi-Flow Y Pipe: HP Gains 15-20. Direct Bolt-in Replacement / No modification necessary

Fits:
Porsche 997 Turbo MKII

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

97501

The product you are viewing cross references to these numbers

Porsche's new DFI (Direct Fuel Injection) intake is a totally and completely redesigned intake system developed to deliver improved performance, fuel consumption and emissions by optimizing the air fuel mixture directly inside the combustion chamber.



The DFI Porsche engine package is a finely tuned performance machine and additional power has proved difficult to find. The unique design of Porsche's new DFI intake system posed very challenging tuning hurdles but once again IPD developed a design that out performs the factory intake system without compromising reliability and drive-ability.

This innovative and revolutionary IPD DFI Intake Plenum employs the patented "Y" design as well as an enlarged plenum area that allows for improved intake air speed and velocity resulting in performance increases without any loses in power.

The all new specifically designed IPD 3.6L DFI intake Plenum is a direct bolt-on upgrade that replaces the factory air distributor and utilizes all pre-existing factory hardware including the OE factory throttle body.

The improved IPD intake design creates increased air velocity and air speed resulting in impressive power and torque gains for Porsche driving enthusiast.

The superior design of the DFI IPD Plenum provides an additional 14 horsepower at the wheels. Unlike previous naturally aspirated IPD plenums that delivered stronger gains in the mid range, the new IPD DFI Plenums deliver a similar shaped power curve as the factory but are considerably stronger from the mid range to redline without any power loses down low.

Installation of the new IPD 3.6L DFI Plenum is relatively straight forward and can be installed by mechanically inclined DIY customers although IPD strongly recommends installation be performed by a trained and qualified Porsche technician.

Fits:
Porsche 997 GEN2 3.6L

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

97482-3.6

The product you are viewing cross references to these numbers

Porsche's new DFI (Direct Fuel Injection) intake is a totally and completely redesigned intake system developed to deliver improved performance, fuel consumption and emissions by optimizing the air fuel mixture directly inside the combustion chamber.



The DFI Porsche engine package is a finely tuned performance machine and additional power has proved difficult to find. The unique design of Porsche's new DFI intake system posed very challenging tuning hurdles but once again IPD developed a design that out performs the factory intake system without compromising reliability and drive-ability.

This innovative and revolutionary IPD DFI Intake Plenum employs the patented "Y" design as well as an enlarged plenum area that allows for improved intake air speed and velocity resulting in performance increases without any loses in power.

The all new specifically designed IPD 3.8L DFI intake Plenum is a direct bolt-on upgrade that replaces the factory air intake distributor and utilizes all pre-existing factory hardware and throttle body.

The improved IPD intake design allows for smoother, less turbulent and more efficient air flow resulting in impressive power and torque gains for Porsche driving enthusiasts.

The superior design of the DFI IPD Plenum provides an additional 15 horsepower at the wheels. Unlike previous naturally aspirated IPD plenums that delivered stronger gains in the mid range, the new IPD DFI Plenums deliver a similar shaped power curve as the factory but are considerably stronger from the mid range to redline without any loses in power down low.

Installation of the new IPD 3.8L DFI Plenum is relatively straight forward and can be installed by mechanically inclined DIY customers although IPD strongly recommends installation be performed by a trained and qualified Porsche technician.

Fits:
Porsche 997 GEN2 3.8L S

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

97482-3.8

The product you are viewing cross references to these numbers

Fabspeed's Carbon Fiber Competition Intake System installed on a Porsche 997.2 Carrera.



Improves cold air induction into the engine and improves power and sound through the rev range; constructed with genuine carbon fiber for strength and durability.

FEATURES:
• Fits all Porsche 997.2 Carrera vehicles 2009-2011
• Improves power by 16 whp and 14 ft-lbs of torque at 5500rpm
• Includes dual dry-style air filters which do no require oiling; simply wash with warm water and re-use
• Intake constructed from genuine carbon fiber
• Direct bolt-on replacement for the factory air box
• Fabspeed Lifetime Limited Warranty


Please note: This is a special-order item manufactured to order. In some cases, please allow 4 – 5 weeks for the delivery. Special order items cannot be cancelled from this supplier once your order has been placed.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

FSPOR9972COMPAI

The product you are viewing cross references to these numbers

Performance engine mounts (PAIR). Included two M12 x 1.75 Nuts



Separate inserts available for varying densities
Shore ratings 65A Street (available separately)
Shore ratings 75A Fast Road (included in engine mounts)
Shore ratings 85A Track (available separately)

Fits:
Porsche 964 C2 / C4 / RS / Turbo
Porsche 993 C2 / C4 / RS / Turbo
Porsche 996 C2, C4, C4S, Turbo, GT2, GT3
Porsche 997 C2, C2s, C4, C4s, Turbo, GT2, GT3

Please note: the threads needs to be treated with loctite before installation (not sold with the product).

Replacing your factory engine mounts with these performance semi-solid mounts will dramatically decrease engine movement which then will result in better acceleration and handling of your Porsche.

CNC machined mounts with PU bushes are absolute must have for any car on track or on the street. Very easy to replace by experienced DIYers.

For 911 & Porsche world article / fitment guide pdf please CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3609309625

The product you are viewing cross references to these numbers

Tuneable Semi-Solid Engine Mount.
SET OF 2 Includes three pairs of inserts in varying densities

 

Fits:
Porsche 964/993/996/997

The Rennline Tune-able Engine Mount for the 964, 993, 996, and 997 offers the ultimate in adjust ability for your car. Replacing your compliant factory mounts will decrease engine movement resulting in better acceleration, handling and significantly increased shifter feel. This is the ultimate solution for almost any car, and allows you to tune our mounts for the way you drive. Our mounts are CNC machined from billet aluminium and include three pairs of inserts in varying densities. Tune your mounts by using the softer inserts to reduce engine slop and avoid missed shifts in your street car, or utilise the stiffest inserts to get the most from a more focused track car. You can even mix and match, giving you 9 possible combinations to let you dial in our mount to your specifications. Here at Rennline we know you want your Porsche to be flawless, and that is why we are Driven to Improve Excellence.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

M18

The product you are viewing cross references to these numbers

RSS Performance engine mounts (PAIR).



Fits:

Porsche 996 C2, C4, C4S, Turbo, GT2, GT3
Porsche 997 C2, C2s, C4, C4s, Turbo, GT2, GT3

With factory hydraulic engine mounts, the drive train will move independent of the chassis during acceleration and cornering loads. This movement can upset the balance of the vehicle and create negative handling effects.

RSS Tarmac Series Performance Engine Mounts minimise these effects by utilising specialised polyurethane bushings which offer a firmer, more direct driving feel with optimum feedback. This upgrade will not adversely effect ride quality or cause knock sensor issues commonly associated with solid engine mounts.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

624

The product you are viewing cross references to these numbers

Engine mount bush kit
Shore rating 65A for 3609309625 performance engine mounts



Fits:
Porsche 996 C2, C4, C4S, Turbo, GT2, GT3
Porsche 997 C2, C2s, C4, C4s, Turbo, GT2, GT3

Shore ratings 65A Street
Shore ratings 75A Fast Road (including in engine mounts)
Shore ratings 85A Track


For 911 & Porsche world article / fitment guide pdf please CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3609309665

The product you are viewing cross references to these numbers

Engine mount bush kit
Shore rating 85A for 3609309625 performance engine mounts



Fits:
Porsche 996 C2, C4, C4S, Turbo, GT2, GT3
Porsche 997 C2, C2s, C4, C4s, Turbo, GT2, GT3

Shore ratings 65A Street
Shore ratings 75A Fast Road (including in engine mounts)
Shore ratings 85A Track


For 911 & Porsche world article / fitment guide pdf please CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3609309685

The product you are viewing cross references to these numbers

High flowing turbo inlet hose kit



To Fits:
Porsche 911 997.2 Turbo 2010 to 2015 with 6-Speed / PDK gearbox.

Significant advantages with Do88's high flowing turbo inlet pipes:

• Much larger overall inner diameter for improved air flow, do88's is 26% higher!
•The hose has 2.5 inch (63mm) internal diameter at the smallest location.
•Smooth flow transitions and very smooth internal surfaces for best possible air flow.
•Excellent thermal properties, the hoses will not absorb heat from the engine.
•The hoses are reinforced with stainless steel wire to eliminate the risk of collapse on high engine output!
•See enlarged images for more information.

About the Inlet Pipes:

Do88: It was a real challenge developing new turbo intake hoses for the 997.2 Turbo. The lack of space makes it really difficult to make a set of hoses that outflow the stock OEM plastic pipes. We achieved this and succeeded in maximising the performance but we had to make the small compromise of letting the hoses have no clearance; so they will push or rub in some non-sensitive areas. The hoses are reinforced with stainless steel wire to ensure overall durability and lasting performance.

Our self-developed intake hoses increase air flow; 26% higher than the OEM hoses. We can ensure you the sensation while driving is very different. The improvement in throttle response is immense, making the car feel so much more refined and alert. This upgrade makes it become what it should have been from the start. This is an improvement no test figures can explain, it has to be perceived behind the wheel of a 997 turbo!

Included in the kit:

• 2 x Wire reinforced silicone hoses
• 2 x CNC machined VTG adaptors
• All hardware for installtion!

Magnetic oil drain plug, with a seal ring (washer).
Hard Anodized Aluminum, with magnet, 18 x 1.5mm



Fits:
Porsche 996 1997-04
Porsche 997 2005-08
Porsche 986 Boxster 1997-04
Porsche 987 Boxster 2005-08
Porsche 987C Cayman 2005-08

A magnetic sump oil drain plug is a type of oil drain plug that contains a small magnet designed to attract and capture metallic particles that may be present in your engine's oil. While this type of drain plug is not exclusive to Porsche and can be used in various vehicles, it can provide several benefits, including:

Improved Engine Longevity: The magnet in the drain plug helps to capture tiny metal particles, such as iron, steel, or aluminum, that may circulate in the engine oil. Removing these particles can reduce wear and tear on engine components, potentially extending the engine's lifespan.

Enhanced Engine Performance: By reducing the presence of contaminants in the oil, a magnetic drain plug can help maintain the oil's lubricating properties, which is crucial for smooth engine operation. Clean oil can also contribute to improved fuel efficiency.

Early Detection of Problems: As the magnetic drain plug collects metallic debris, it can serve as an early warning system. By inspecting the drain plug during oil changes, you can get an idea of the engine's condition and detect any unusual wear or damage before it becomes a major issue.

Reduced Maintenance Costs: Regularly inspecting and cleaning a magnetic drain plug can prevent larger issues from developing over time. Addressing potential problems early can save you money on more extensive repairs down the road.

Peace of Mind: Knowing that you are taking steps to protect your engine from premature wear and tear can give you peace of mind as a vehicle owner. It's a relatively inexpensive and simple modification that can provide added assurance.

Easy Installation: Magnetic drain plugs are typically straightforward to install. They often replace the existing drain plug and require no special tools or modifications.

While magnetic drain plugs can offer these benefits, it's essential to remember that they are not a substitute for regular oil changes and proper maintenance. Regular oil changes with the appropriate oil and filter are still crucial for the health and longevity of your engine. Additionally, magnetic drain plugs may not capture all types of contaminants, so they should be seen as a supplementary measure rather than a comprehensive solution.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90021900930

The product you are viewing cross references to these numbers

Extreme high flow performance Y-Pipe.



To Fit:
Porsche 997.2 Turbo models 2010 to 2012

At the beginning of the development process of this product we spent a lot of time thinking what would be the preferred way to build a Y-pipe; here is the result of our conclusions and development process!

Significant advantages with Do88's Y-pipe compared to the OEM pipe:

• Much larger inner diameter for improved air flow, do88 62% higher!
• 70mm mandrel bent aluminium pipes.
• Smooth flow cast collector part.
• Smooth internal surface for best air flow.
• Comes with high quality silicone hoses and accessories for installation.
• See enlarged images for more information!

Our pipe has both a very good flow rate and a low weight which is achieved by combining mandrel bent lightweight pipes with a high quality 3D freeform designed cast joint between them. Onto the cast part we then welded CNC-machined connections for bov and breather hoses.This construction adds a lot of performance but only small amount of extra weight. Do88 Performance Y-pipe weight 1,52 kg (3,35 lb) OEM plastic pipe weight 1,38 kg (3,04 lb) and a competitors cast performance pipe weight 2,76kg (6,08 lb)!

The pipes are then finished in a high quality powder coat that makes them look as good as they perform! You can choose between the more discrete semi gloss black and a fresh silver metallic finish.

The kit also includes 2 high quality custom designed silicone hoses which are available in two different versions. Which version you need depends on if you will install the Y-pipe together with the OEM intercoolers or the do88 performance intercoolers.

When it comes to air flow performance our Y-pipe totally outperforms the OEM Y-pipe by 62% increased flow at the same pressure drop! On our final tests of this Y-pipe together with our intercoolers on a Stage 1 tuned 997.2 Turbo PDK we measured a great performance increase. In all tests the car was driven in Sport Plus, automatic gear change and AC off. From our five in a row full throttle accelerations between 40-270 km/h (25-168 mph) we have very accurate and consistent test data for the range 50-250 km/h (31-155 mph). When analyzing the numbers, we found that we cut down the acceleration time for 50-250 km/h (31-155 mph) by 3 seconds!

Included parts in this kit:

• Full aluminium performance Y-pipe
• Silicone hoses
• Hose clamps
• Hose adaptors if the Y-pipe will be installed together with OEM intercoolers

Rennline intake ducts carbon fibre. 

Fits:
Porsche 997 turbo Gen 1 - 2007 to 2009
Porsche 997 turbo Gen 2 - 2010 to 2013

Product Description

Rennline’s carbon fibre 997 Turbo intake ducts are a great way to give your 997's engine bay a modern facelift and these work in conjunction with our 997 Turbo Intake, to increase airflow and performance. 

Made from high quality carbon fibre using the latest technology, our intake ducts are designed with the dimensions of the OEM pieces for a factory fit and finish while adding a bit of style. 

Take your old plastic pieces out and install ours in their place. Installs in minutes using new factory hardware.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

M66

The product you are viewing cross references to these numbers

Restrictor plate kit. Porsche 997 Cup / Porsche 991 Cup



Fits:
Porsche 997 GT3 Cup
Porsche 991 GT3 Cup 

These restrictors mount over the front of the intake throttle body and under the intake boot.

Take Control with Our Restrictor Plate Kit
Harness the power of your vehicle with our Restrictor Plate Kit. It’s designed for the late 997 and 991 air filter system. These precision machined restrictors mount over the front of the intake throttle body and under the intake boot.

What’s Included in Your Purchase
Your purchase includes a set of 10 distinct restrictor plates. This array provides a variety of restriction options. Hence, you can fine-tune your vehicle’s horsepower to your exact needs. This ensures optimal performance for any scenario.

This includes a set of 10 plates that fit over the front of the throttle housing under the intake boot.  Easy to install and easy to remove as needed.

Ideal for NASA GTS Preparations
Are you prepping for NASA GTS? Our Restrictor Plate Frame is the perfect tool for you. It allows precise horsepower calibration. Consequently, you can achieve your desired performance level each time. We’ve tested this plate frame on a 996 cup car with fantastic results. The horsepower reduced smoothly, and the air/fuel ratio remained unaffected.

Why Choose Our Restrictor Plate Kit
Our Restrictor Plates offers precise horsepower control. It’s a must-have for racing enthusiasts and those seeking to tailor their vehicle’s performance. Experience the difference of custom tuning with this reliable, efficient tool. Invest in our Restrictor Plates and experience the thrill of tailored performance today.

Fits all 997 Cup and all 991 Cup